Crestron DMF-CI-8 Supplemental Manual Download | Manualshive

Page: 11 / 30

background image

Supplemental Guide – DOC. 7861C

DMF-CI-8: DM NVX and DMCF Card Chassis

•

7

Card Status and Configuration Menu

_

DM-NVX-350C-00107_



Device Mode



Input Routing

Network Settings

Diagnostics

NOTE:

The Device Mode and Input Routing menu items appear on the menu for

the DM-NVX-350C and DM-NVX-351C cards only.

The following sections provide information about viewing card status and

configuring various functions of a card.

Configure the Device Mode

NOTE:

Device mode configuration is applicable to the DM-NVX-350C and DM-NVX-351C

cards only.

Device mode configuration allows the operating mode of a DM NVX card to be changed

from a receiver to a transmitter or from a transmitter to a receiver. By default, a

DM NVX card is configured as a receiver.

To configure the device mode:

1.

On the card status and configuration menu, select Device Mode.

Card Status and Configuration Menu

_ DM-NVX-350C-00107_



Device Mode



Input Routing

Network Settings

Diagnostics

The Device Mode menu appears on the display for the selected card.

Device Mode Menu

_ DM-NVX-350C-00107_



Device Mode



Mode Receiver

e

Lock Unlocked

«
...
9
10
11
12
13
...
»

Summary of Contents for DMF-CI-8































Reviews:

No comments

Related manuals for DMF-CI-8

Brand: National Instruments Pages: 14

Brand: H&S Pages: 32

Brand: Supermicro Pages: 98

Supero SC936 Series

Brand: Supermicro Pages: 84

Brand: Lantronix Pages: 15

Brand: Intel Pages: 35

Brand: HUBER+SUHNER Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands