CLX-1DIM8
8 Channel Dimmer Module, Single Feed
crestron.com
|
800.237.2041
>
8 channels of dimming for incandescent, magnetic low-voltage,
neon/cold cathode, and dimmable 2-wire fluorescent loads
>
Two independent 4 channel dimmers in a single module
>
Dual or single 120 Volt feed
>
Air-gap relays on every channel output
>
Override preset capability
>
Convection cooled
>
Occupies 1 module space in a CAEN or CAEN-MLO
automation enclosure
>
Easy termination using CLT-Series terminal block
As part of a complete Crestron lighting system, the CLX-1DIM8 lighting
control module provides 8 channels of dimming for incandescent,
magnetic low-voltage, neon/cold cathode, and dimmable 2-wire
fluorescent loads. Each channel is rated for 1920 Watts, with a total
module rating of 1920 Watts. Air-gap relays are provided on every channel
output allowing individual circuits to be serviced without disabling the
entire module.
CLX-Series dimmers are rigorously built using 40 Amp triacs and oversized
heat sinks for ultimate reliability. Split-bobbin transformers and ground
referenced electronics deliver superior performance. Lamp flicker is
minimized through Crestron’s innovative zero-crossing detection technique
backed by proprietary firmware. Low-maintenance convection cooling
assures quiet and trouble-free operation.
An override feature allows each channel to be adjusted to a preset state
during setup. In the event that Cresnet communications should be
disrupted for any reason, a simple contact closure can be used to activate
the override presets on a global or semi-global basis.
The CLX-1DIM8 occupies a single module space in any
CAEN
or
CAEN-MLO
automation enclosure. Termination of high-voltage wiring to the
module is facilitated by a
CLT-1DIM8
terminal block, sold separately to
enable termination of the wiring any time prior to installing the module.
CLX modules are controlled by the
PAC2
and
PAC2M
professional
automation control systems via the Cresnet network. A 5-wire link provides
bussing of the Cresnet and override signals between modules within an
enclosure (interconnect jumpers included).
SPECIFICATIONS
Load Ratings
Dimmer Channels:
8
Per Channel:
16 Amps (1920 Watts)
Module Total:
16 Amps (1920 Watts)
Minimum Load:
25 Watts
Load Types:
Incandescent, Magnetic Low-voltage, Neon/Cold Cathode,
Dimmable 2-Wire Fluorescent
Power Requirements
120 Volts AC, 50/60Hz, single-phase
Connectors on Module
Module Interconnect:
(2) 5-pin 0.156 inch headers;
Cresnet/Override interconnect ports;
Connect to PAC2, PAC2M, CAEN-BLOCK, or adjacent CLX-Series module
using interconnect cable provided
Connections via CLT Terminal Block (sold separately)
LINE:
(1) DIN rail terminal block, black, line power input
DIM 1 - 8:
(8) DIN rail terminal blocks, red, channel outputs
N IN:
(1) DIN rail terminal block, white, line input neutral
N OUT 1 - 8:
(8) DIN rail terminal blocks, white, channel output neutrals
Buttons
SETUP:
Used for manual channel activation and TSID
LED Indicators
PWR:
(green) Indicates line power is applied to the LINE terminal
NET:
(yellow) Indicates communication with the control system
1 – 8:
(red x8) Indicates state of each channel
SETUP:
(red) Indicates unit is in setup/manual mode
Environmental
Temperature:
32° to 104°F (0° to 40°C)
Humidity:
10% to 90% RH (non-condensing)
Heat Dissipation:
26 BTU/Hr + (4.7 BTU/Hr x Load Current in Amps), 101
BTU/Hr at maximum load
Shown with CLT-1DIM8 Terminal Block