CLW-DIM, DIMS, & SLVD(W/A/B)
Operating Buttons and Switches
NOTE:
The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG. The GRAY (Cresnet) wires are #22 AWG. The
BLACK wire (Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
The -DIM, -DIMS, and -SLVD feature three pushbuttons
(one large, and two-small). The -DIM and -DIMS also
have a three-position mode selection switch. The function
of each button is determined by the position of the mode
selection switch. Refer to the following diagram.
CLW-DIMS with CLW-SLVD Wiring
NOTE:
The -SLVD does not have a mode selection
switch. It will act in the same mode as the -DIMS.
NOTE:
The -DIMS must be installed in the same wallbox
that contains the connections to the load.
Buttons of CLW-DIM, -DIMS, and -SLVD
Button 1
Button 2
Button 3
Mode Selection Switch
(-DIM & -DIMS Only)
The following wiring diagram illustrates installation of
the -DIMS with a -SLVD.
Wiring Diagram of CLW-DIMS with multiple CLW-SLVDs
Hot
Neutral
Load
RED
CLW-DIMS
BLACK
WHITE
CLW-SLVD
BLUE
BLACK
BLUE
Ground
Ground
GREEN
GREEN
LINE
120VAC
60Hz
WHITE
Ground
GREEN
BLACK
BLUE
CLW-SLVD
WHITE
Cresnet
OFF
When the mode selection switch is in the “OFF” position,
the buttons will not have any function and the load is
disconnected from the power source. This
must
be used
when changing light bulbs to ensure that the load is fully
disconnected from power.
NOTE:
Do not connect the BLUE (Slave) wire to the
Black (Hot) or RED (Load) wires.
ADJ
When the mode selection switch is in the “ADJ” position,
the large button is used to switch between the “Button 1-
High” and “Button 1-Low” presets (typically “On” and
“Off”). The lighting level can be manually adjusted using
the two small buttons to raise (right button) and lower
(left button) the lighting level.
NOTE:
The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG. The GRAY (Cresnet) wires are #22 AWG. The
BLACK wire (Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
If the lighting level is to be stored as a preset, move the
mode selection switch to the PRE position. Press and hold
the desired preset button until the LED flashes.
NOTE:
If a -DIMS is installed without a -SLVD, the
BLUE lead (Slave) should be capped.
PRE
5. Splice the gray wires of the -DIM or -DIMS to
the Class 2 low voltage wires connected to the
Crestron control system, a Crestron power
supply, a Crestron C2N-NPA8, or a Crestron
connection block device. Push the wires and the
splices into a hole in the drywall to provide the
necessary separation.
NOTE:
Before storing a preset, the lighting must be
adjusted to the desired level while in the ADJ mode.
When the switch is in the PRE position, it is in the preset
mode and can be used to recall and/or store preset lighting
levels. The large button is used to recall and/or store the
“Button 1-High” and “Button 1-Low” presets. The lower
left button (button 2) is used to recall and/or store preset
level two. The lower right button (button 3) is used to
recall and/or store preset level three. Pressing and
releasing a button will fade to the preset lighting level
over a three second period. Tapping a button while the
light is fading will cause the light level to “jump” to the
preset without fading. Pressing and holding a button until
the LED flashes will store the current lighting level.
6. Push all Class 1 power wires back into the
wallbox and fasten the device to the wallbox
with the provided screws.
7. Attach decorative faceplate.
8. Restore
power.
Installation Guide – DOC. 5995B
Stand Alone Wall Box Dimmer: CLW-DIM, DIMS, & SLVD
•
5
