manualshive.com logo in svg

Crestron Cameo C2N-CBF, Operations & Installation Manual

Share
Download
Crestron Cameo C2N-CBF Operations & Installation Manual Download Page 39

Crestron 

C2N/C2NI-CB Series

 Cameo

™

 Keypads

 

7. 

Select a file and click 

Open. 

When the “SIMPL Program” 

window re-opens click 

Send

. 

Firmware Upgrade 

A firmware 
upgrade file 
has the 
extension .upg. 

 

To take advantage of all the Cameo keypad features, it is important that 
the unit contains the latest firmware available. Please check the Crestron 
website for the latest version of firmware. Not every product has a 
firmware upgrade, but as Crestron improves functions, adds new features, 
and extends the capabilities of its products, firmware upgrades are 
posted. To upgrade the firmware, complete the following steps. 

1. 

Make sure that “Communication Settings” that begins on page 
29 has been performed. 

2. 

Open Crestron Toolbox.  

3. 

Open the Network Device Tree (the firmware upgrade 
function is also available in the SMW Program Tree window). 

4. 

Right-click on the device and select 

Functions | Firmware

. 

Network Device Tree Window – Right-Click Sub Menu 

 

5.  The “Firmware” window displays the model and current 

firmware version.  

Operations & Installation Guide - DOC. 6346A 

Cameo™ Keypads: C2N/C2NI-CB Series  

•

  35 

Summary of Contents for Cameo C2N-CBF

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands