manualshive.com logo in svg

Crestron Cameo C2N-CBF, Operations & Installation Manual

Share
Download
Crestron Cameo C2N-CBF Operations & Installation Manual Download Page 20

Cameo

™

 Keypads 

Crestron 

C2N/C2NI-CB Series 

Decorator Mounting Installation 

The keypad for Decorator mounting installation is supplied partially 
assembled along with several items as listed in the following table.  

Supplied Parts/Assemblies – Decorator Mounting 

QTY ITEM 

DESCRIPTION 

1 

Rear housing and switch assembly 

Rear housing with switch circuitry attached 

1 

Bezel assembly 

Bezel and metal plate assembly, with ground wire 

1 

4-pin female mini network 
connector 

Used to connect Cresnet network cable to the keypad 

2 

Screws, Black, Phillips pan head, 
4-40 x 3/16” 

Used to attach the bezel assembly to the keypad rear 
housing and switch assembly 

6 

Single row button cap 

Switch cover for a single row switch 

3 

Double row button cap 

Switch cover for two switches that function as one 

2 

Triple row button cap 

Switch cover for three switches that function as one 

2 

Single row spacer 

Switch cover for single non-operational switch 

1 

Double row spacer 

Switch cover for two non-operational switches 

1 

Triple row spacer 

Switch cover for three non-operational switches 

1 

Plastic button support 

Used to hold the button caps/spacers together in 
position 

2 

Screws, Steel, Phillips, pan head, 
6-32 x 7/8” 

Used to attach the assembled keypad to a back box 

Assemble the keypad as described in the following steps. Refer to the 
accompanying illustrations. 

1.  Arrange the button caps 

and/or spacers in position 
according to the program 
plan. Attach the plastic 
button support to the 
button caps/spacers, and 
put the assembled parts in 
place on the rear housing 
and switch assembly. 

2.  Carefully position the 

bezel assembly, LED edge 
first, down and over the 
button caps/spacers and 
rotate slightly into 
position on the rear 
housing and switch assembly. 

Button Caps

and Spacers

Plastic

Button

Support

Rear Housing

and Switch

Ass’y

16  

•

  Cameo™ Keypads: C2N/C2NI-CB Series 

Operations & Installation Guide - DOC. 6346A 

Summary of Contents for Cameo C2N-CBF

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands