manualshive.com logo in svg

Crestron C2N-VEQ4, Operation Manual, Page: 19 / 40

Share
Download
Crestron C2N-VEQ4 Operation Manual Download Page 19

Crestron 

C2N-VEQ4

 

Cresnet 4-Channel Digital Volume Control

 

Operations Guide - DOC. 6135A 

Cresnet 4-Channel Digital Volume Control: C2N-VEQ4  

•

  15 

Expanded PRO2 System Tree 

 

C2Net Device Slot in Configuration Manager 

To incorporate a C2N-VEQ4 into the system, drag the C2N-VEQ4 from the Cresnet 
Control Modules | Cresnet Audio Modules folder of the 

Device Library

 and drop it in 

System Views

. The PRO2 system tree displays the C2N-VEQ4 in Slot 9, with a 

default Net ID of 12 as shown in the following illustration. 

NOTE:

  The first C2N-VEQ4 in a system is preset with a Net ID of 12 when its 

symbol is dragged into the upper pane of 

System Views

. Additional units are assigned 

different Net ID numbers as they are added. 

C2Net Device, Slot 9 

 

Setting the Net ID in Device Settings 

Double-click the C2N-VEQ4 icon to open the “Device Settings” window. This 
window displays the C2N-VEQ4 device information. If necessary, select the 

Net ID

 

tab to change the unit’s Net ID, as shown in the following figure.  

C2N-VEQ4 “Device Settings” Window 

 

Summary of Contents for C2N-VEQ4









































Reviews:

No comments