LEXINGTON PREMIUM PACK 16
LEXI9WPP16-100 Rev A (04-18)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
LEXI9WPP16
Lexington Premium Pack 16
• Start by assembling the Lexington tower. Instructions and hard-
ware are in the cartons noted at left.
The gym is rotated 90° from
the position shown in the instructions.
The components of this gym can be combined with others to
create different play sets. This is the best order of assembly
to create this specific set.
Read this sheet and all instructions included with the
different parts before assembly.
See the Instructions and Owner's Manual included in carton
63007-445 for important safety information.
Dimensions of assembled package:
27' 9" wide x 15' 7" deep x 12' 9" tall
Cartons for this Play Set:
1 63007-421
Lexington Gym 1 (Hardware)
1 63007-422
Lexington Gym 2
1 63007-423
Lexington Gym 3
1 63007-445
Lexington Roof (Hdwre & Instr)
1 SH946-102 Access Ladder, 5ft
1 AG942-400 Access Ladder Handles (Hdwre & Instr)
1 63058-202
4 Position Swing Beam
1 63060-222
9ft Swing Beam Legs (Hdwre & Instr)
1 50546-777
3 Swings, 1 Trapeze
1 15166-400
10 ft. Super Wave Slide
1 SM964-402 Gable Fans (Hdwre & Instr)
1 SM963-402 Dormer (Hdwre & Instr)
1 AH201-102Q Rock Climbing Wall (Hdwre & Instr)
1 63090-222
Chain Climber Frame
1 63089-606
Chain Cargo Net
1 SC909-800Q Lexington Play Walls
1 SC910-800Q Lexington Play Floor
1 63008-221
Skybox 1 (Hdwre & Instr)
1 63008-222
Skybox 2
1 SJ926-810 Skybox Wood Roof (Hdwre & Instr)
1 8400-202
Spiral Slide, Green (Hardware)
1 63033-102
Spiral Mount (Hdwre & Instr)
1 AG943-400 Slide Handle (Hdwre & Instr)
1 SH304-101Q Pinnacle Rock Wall (Hdwre & Instr)
15 1/2"
7 1/4"
3"
0"
• Wait to install the Access Ladder, Slide, and
Wall Slats until after the rest of the play set is
complete.
• Lex step 2. Omit the sandbox end from the end
of the gym adjacent to the Skybox. It will be
altered to fit the Skybox.
• Lex step 7. Do not install the safety rail.
• Lex step 14. Do not install the end wall support
on the Skybox end of the tower.
• Lex step 15. The swing mount isn't needed.
• Lex step 25. Before installing the roof, find the
post where the swing beam will mount. Drill
7/16" diameter holes through the post at 3",
7-1/4" and 15-1/2" below the top of the post as
shown at right.The beam will be mounted to the
Dormers
front of the post using these holes. Insert one 5/16" weld nut into
the top hole on the inside face of the post. Be sure the threads on
the weld nut are clear, it will be captured by the roof support. Install
the roof.
• Mount the Swing Beam using instructions and hardware includ-
ed in 63060-222. Mount the beam to the previously drilled holes
shown above right rather than the way shown in the instructions.
You may need to temporarily disconnect the roof from the post to
put the beam in place.
