Crane BARNES 6SE-EHA Series, Installation And Operation Manual

Page: 7 / 22

MODEL HP VOLT PH RPM NEMA FULL LOCKED CORD CORD CORD WINDING
NO. (Nom) CODE LOAD ROTOR SIZE TYPE OD RESISTANCE
AMPS AMPS MAIN
6SE10036EHA 10 230 3 1150 H 31.0 161.0 8/4 SOW-A 0.985 0.39
6SE10046EHA 10 460 3 1150 H 15.5 80.5 8/4 SOW-A 0.985 1.59
6SE15036EHA 15 230 3 1150 G 39.0 218.0 8/4 SOW-A 0.985 0.24
6SE15046EHA 15 460 3 1150 G 19.5 109.0 8/4 SOW-A 0.985 0.99
6SE20036EHA 20 230 3 1150 G 54.0 284.0 6/4 SOW-A 1.125 0.18
6SE20046EHA 20 460 3 1150 G 27.0 142.0 6/4 SOW-A 1.125 0.73
6SE25036EHA 25 230 3 1150 G 68.0 346.0 4/4 SOW-A 1.350 0.13
6SE25046EHA 25 460 3 1150 G 34.0 173.0 4/4 SOW-A 1.350 0.53
6SE30046EHA 30 460 3 1150 G 40.0 210.0 2/4 SOW-A 1.500 0.36
6SE30034EHA 30 230 3 1750 G 78.0 414.0 2/4 SOW-A 1.500 0.11
6SE30044EHA 30 460 3 1750 G 39.0 207.0 2/4 SOW-A 1.500 0.45
6SE40034EHA 40 230 3 1750 F 104.0 550.0 2/4 SOW-A 1.500 0.10
6SE40044EHA 40 460 3 1750 F 52.0 275.0 2/4 SOW-A 1.500 0.33
6SE50044EHA 50 460 3 1750 F 63.0 336.0 4/4 SOW-A 1.350 0.16
6SE60044EHA 60 460 3 1750 F 77.3 410.0 2/4 SOW-A 1.500 0.15
6SE75044EHA 75 460 3 1750 F 92.0 504.0 2/4 SOW-A 1.500 0.11
6SE100044EHA 100 460 3 1750 G 120.0 703.0 1/4 SOW-A 1.680 0.08
Winding Resistance ± 5%. Pump rated for operation at ± 10% voltage at motor.
Moisture/Temperature sensor cable for all models is 18/5 SO, 0.476 O.D.
SECTION: D START-UP OPERATION
D-1) Check Voltage and Phase:
Before operating pump, compare the voltage and phase information
stamped on the pump identification plate to the available power.
D-2) Check Pump Rotation:
Before putting pump into service for the first time, the motor rotation
must be checked. Improper motor rotation can result in poor pump
performance and can damage the motor and/or pump. To check the
rotation, suspend the pump freely, momentarily apply power and
observe the "kickback". "Kickback" should always be in a
counter-clockwise direction as viewed from the top of the pump motor
housing.
D-2.1) Incorrect Rotation for Three-Phase Pumps:
In the event that the rotation is incorrect for a three-phase installation,
interchange any two power cable leads at the control box.
DO NOT
change leads in the cable housing in the motor. Recheck the
"kickback" rotation again by momentarily applying power.
D-2.2) Incorrect Rotation for Single-Phase Pumps:
In the unlikely event that the rotation is incorrect for a single phase
pump, contact a Barnes Pumps Service Center.
D-3) Start-Up Report:
Included at the end of this manual are two start-up report sheets,
these sheets are to be completed as applicable. Return one copy to
Barnes Pumps, Inc. and store the second in the control panel or with
the pump manual if no control panel is used. It is important to record
this data at initial start-up since it will be useful to refer to should
servicing the pump be required in the future.
D-3.1) Identification Plate:
Record the numbers from the pump identification plate on both
START-UP REPORTS provided at the end of the manual for future
reference.
D-3.2) Insulation Test:
Before the pump is put into service, an insulation (megger) test
should be performed on the motor. The resistance values (ohms) as
well as the voltage (volts) and current (amps) should be recorded on
the start-up report.
D-3.3) Pump-Down Test:
After the pump has been properly wired and lowered into the basin,
sump or lift station, it is advisable to check the system by filling with
liquid and allowing the pump to operate through its pumping cycle.
The time needed to empty the system, or pump-down time along with
the volume of water, should be recorded on the start-up report.
7