background image

20

MODEL NUMBER 143.044500

CRAFTSMAN 4-CYCLE ENGINE

KEY    PART
NO.     NO.              DESCRIPTION

- -        640339        Carburetor (Includes Key Number 184 of Engine Parts List)
1         631615        Throttle Shaft & Lever Assembly 
2         631767        Throttle Return Spring
4         631184     *  Dust Seal Washer
5         631183     *  Dust Seal (Throttle)
6         640070        Throttle Shutter
7         650506     *  Shutter Screw
16       631807        Fuel Fitting
17       651025        Throttle Crack / Idle Speed Screw
18       630766        Tension Spring
20       640016        Screw, Idle Restrictor
20A     640200        Cap, Idle Restrictor Screw (Black)
25       631867        Float Bowl
27       631024     *  Float Shaft
28       632802        Float (Plastic)
29       631028     *  Float Bowl “O” Ring
30       631021A  *  Inlet Needle, Seat and Clip (Includes Key Number 31)
31       631022        Spring Clip
35       640259        Primer Bulb / Retainer Ring
36       640080        Main Nozzle Tube 
36A     632766        Carburetor Tube
37       632547     *  “O” Ring, Main Nozzle Tube
40       640030        High Speed Bowl Nut
44       27110A    *  Bowl Nut Washer
47       630748     *  Welch Plug, Idle Mixture Well
48       631027     *  Welch Plug, Atmospheric Vent
60       632760B     Repair Kit (Includes All Items Marked * )

Summary of Contents for 944.364300

























Reviews: