Craftsman 390.250255 Owner'S Manual Download | Manualshive

Page: 1 / 12

background image

OWNER’S

MANUAL

MODEL NO.

390.250255

CAUTION:
Read and Follow
All Safety Rules and
Operating Instructions
Before First Use of
This Product.

Save This Manual For
Future Reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

• Safety Instructions
• Installation
• Electrical
• Maintenance
• Repair Parts

PRINTED IN U.S.A.

SHALLOW WELL
JET PUMP

®

Form No.

F642-9903

(Rev. 4/19/01)

1
2
3
...
»

Summary of Contents for 390.250255













Reviews:

No comments

Related manuals for 390.250255

Brand: Water Factory Systems Pages: 15

Brand: SAER Elettropompe Pages: 16

Brand: Gude Pages: 62

Brand: IWAKI PUMPS Pages: 64

Brand: Rheem Pages: 1

Brand: Grundfos Pages: 35

Brand: Xylem Pages: 21

Brand: Marco Pages: 3

Brand: Trinity Lx Pages: 24

URG250H6N-475-264

Brand: Bradford White Pages: 32

Brand: Ozito Pages: 6

aroSTOR VWL B 270/5

Brand: Vaillant Pages: 240

Brand: DVP Pages: 13

Brand: OmarLift Pages: 32

Brand: Pentair Pages: 12

Myers CPM Series

Brand: Pentair Pages: 12

Brand: CLIVET Pages: 32

Brand: Oceanic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands