background image

 

3

 SAFETY INSRUCTION 

 

  WARNING: BE SURE 

to read and understand all instruction in this manual 

before using this green rotary laser level. Failure to follow all instructions may result in 
hazardous radiation exposure, electric shock, and/or bodily injury.

 

 

 CAUTION:

 Use of controls or adjustments or performance of procedures other 

than those specified herein, may result in hazardous radiation exposure.

 

 

 CAUTION:

 The use of optical instrument with this product will increase eye 

hazard. 

 

IMPORTANT:

 The following labels are on your tool. They

 

indicate where the laser 

light is emitted.   

ALWAYS BE AWARE 

of the 

emission point locations when using 

the green rotary laser level. 

ALWAYS MAKE SURE 

that any 

bystanders in the

 

vicinity of use are made aware of the 

dangers of looking directly into the laser.   

 

  WARNING! LASER LIGHT. LASER RADIATION. 

Avoid Direct Eye Exposure. Do Not Stare into beam. 

1. DO 

NOT 

remove or deface any product labels. Removing 

product labels increases the risk of exposure to laser 

radiation.

 

2. DO 

NOT 

stare directly at the laser beam or project the laser beam directly into the 

eyes of others. Serious eye injury could result.

 

3. DO 

NOT 

place the digital laser level in a position that may cause anyone to stare 

into the laser beam intentionally or unintentionally. Serious eye injury could result.

 

4. DO 

NOT 

use any magnifying optical tools such as, but not limited to telescopes or 

transits to view the laser beam. Serious eye injury could result.

 

5. DO 

NOT 

operate the green rotary laser level around children or allow children to 

operate the tool. Serious eye injury could result.

 

6. ALWAYS 

turn the green rotary laser level “OFF” when not in use. Leaving the tool 

“ON” increases the risk of someone inadvertently staring into the laser beam.

 

7. DO 

NOT 

operate the green rotary laser level in combustible areas such as in the 

presence of flammable liquids, gases or dust.

 

8. 

When using any of the base plates, 

ALWAYS 

check to be sure that the tool is 

Summary of Contents for 320 Series




















Reviews: