background image

2200 MAX PSI* Pressure Washer

Quick Start Guide

Have Questions?

 

Do not return to store. We can help.

Call Customer Service Toll-Free 

1-800-222-3136

Or visit our website 

www.craftsman.com

Unpack pressure washer

Remove everything from carton except pressure washer.

1. 

Open carton completely by cutting each corner from top to bottom. 

2. 

Ensure you have all included items prior to assembly.  

3. 

If items are damaged or missing, call 1-800-222-3136. 

Assemble pressure washer

Place handle (a) against two upright posts.

1. 

Insert two carriage bolts (c) towards outside, through holes at 

2. 

bottom of handle. Fully tighten handle in an upright position with two 

plastic knobs (d).
Place accessory tray (b) over four holes on front side of handle. 

3. 

Push all four tree clips (e) into holes until they sit flat against 

accessory tray.

Add engine oil and fuel

NOTICE:

 Before starting the engine, check oil level and ensure that 

engine is serviced as described in the operator’s manual.

NOTICE:

 DO NOT use E85 fuel. 

NOTICE:

 DO NOT mix oil with fuel. 

Move pressure washer outdoors to a flat, level surface.

1. 

Remove oil fill cap (A). Slowly pour entire contents of oil bottle (h) 

2. 

into oil fill.
Replace and fully tighten oil fill cap.

3. 

Remove fuel cap (B). Add clean, fresh, UNLEADED fuel. Allow space 

4. 

in fuel tank for fuel expansion.
Replace fuel cap. Let any spilled fuel evaporate before starting 

5. 

engine.

© 2009   Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).

Move pressure washer  

to safe operating location

Move pressure washer outdoors to a flat, level surface. Running 

1. 

engines give off carbon monoxide.
Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer 

2. 

including overhead to reduce the risk of exhaust heat or exhaust 

gases igniting nearby combustible material. 

Connect spray gun

Attach high pressure hose (g) to spray gun (j). 

1. 

Remove and discard 2 shipping caps from high pressure outlet  

2. 

and garden hose inlet connections. 
Uncoil high pressure hose and attach to high pressure outlet.

3. 

Connect water supply

NOTICE:

 

If inlet screen is damaged or missing,  

DO NOT use pressure washer, call 1-800-222-3136.

 

Inspect garden hose inlet screen for damage.

1. 

Clean screen if necessary. Refer to operator’s manual for instructions.

2. 

Run cold water through garden hose for 30 seconds to clean out any 

3. 

debris. Garden hose length must not exceed 50 feet. Turn off water 

supply and attach garden hose to water inlet. Tighten by hand.

Start pressure washer

NOTICE:

 

You MUST connect and turn on water supply fully before 

starting engine.

Turn on water supply.

1. 

Put on safety goggles.

2. 

Push trigger lock (red button) on spray gun and pull trigger until 

3. 

water comes out in a steady stream. Release trigger to locked 

position.
Attach quick connect wand (k) to spray gun (j).

4. 

Choose desired spray tip (f), pull back on collar of quick connect 

5. 

wand (k). Insert spray tip and release collar. Tug on spray tip to 

make sure it is securely in place.
Move throttle lever (C) to FAST (

6. 

) position. 

Press primer bulb (D) firmly 5 times, waiting 2 seconds between 

7. 

each push.
When starting engine, position yourself as recommended and grasp 

8. 

starter grip handle and pull slowly until you feel some resistance. 

Then pull rapidly to start engine. After each starting attempt, where 

engine fails to run, always point spray gun in a safe direction, push 

red button and squeeze spray gun trigger to release retained high 

water pressure.

Point gun toward surface to be cleaned. Push trigger lock (red 

9. 

button) and pull trigger to begin spraying.

Stop pressure washer

Let engine idle for 2 minutes.

1. 

Move throttle lever (C) to SLOW (

2. 

) position, 

then STOP ( ) position. 
Turn off water supply.

3. 

Point spray gun in safe direction, push trigger lock, and squeeze 

4. 

spray gun trigger to relieve retained high water pressure.
Disconnect garden hose from pump.

5. 

Disconnect high pressure hose from pump and gun for storage. For 

6. 

long term storage instructions, see operator’s manual.
Remove safety goggles.

7. 

2

3

1

6

8

e

b

4

4

5

7

8

9

10

11

12

13

5

3

4

A

B

Exhaust Port 

Pointed away from 

dwelling openings

6

j

g

7

8

Inlet Screen

Trigger Lock

9

j

f

k

k

10

11

D

12

13

You will need:

•  Utility knife      •  Unleaded fuel      •  Garden hose, 50 feet or less      •  Safety goggles (indirect vented type)

Items Included: 

Operator’s Manual (not shown)

C

12

12

 

WARNING: 

Outdoor use ONLY. DO NOT start or run engine indoors 

or in an enclosed area, even if windows and doors are open. 

Running engines give off carbon monoxide, an odorless, 

poison gas that can cause nausea, fainting or death.

 

WARNING:

 Risk of eye injury. Spray can splash back or propel 

objects. Always wear indirect vented (chemical splash) 

safety goggles, marked to comply with ANSI Z87.1 when 

using or in vicinity of this equipment. NEVER substitute 

safety glasses or dry-condition goggles for indirect vented safety 

goggles.

 

WARNING: 

Starter cord kickback (rapid retraction) can result in 

bodily injury. NEVER pull starter cord without first relieving 

spray gun pressure. Pull starter cord slowly until resistance 

is felt, then pull rapidly. Kickback will pull hand and arm 

toward engine faster than you can let go. High pressure can cause 

spray gun to kickback. Hold spray gun with both hands during use.

 

WARNING:

 Failure to read and follow the operator’s 

manual and all operating instructions can 

result in death, bodily injury, and/or property 

damage. 

 

WARNING: 

Fuel and its vapors are flammable and 

explosive. Turn off engine and wait at least 

2 minutes before refueling. Let spilled fuel 

evaporate before starting engine. Always allow 

space for fuel expansion. 

 

WARNING:

 High pressure water spray can cut 

through skin. Never spray people or animals, 

as injury can result. Spray gun traps high 

water pressure, even when engine is stopped 

and water is disconnected. ALWAYS point spray gun in 

safe direction, press red button and squeeze spray gun 

trigger, to release high pressure, every time you stop 

engine.

 

WARNING:

 Outdoor use ONLY. DO NOT start or run 

engine indoors or in an enclosed area, even 

if windows and doors are open. Running 

engines give off carbon monoxide, an 

odorless, poison gas that can cause nausea, fainting or 

death.

 

WARNING:

 Starter cord kickback (rapid retraction) 

can result in bodily injury. NEVER pull 

starter cord without first relieving spray 

gun pressure. Pull starter cord slowly until 

resistance is felt, then pull rapidly. Kickback will pull 

hand and arm toward engine faster than you can let go. 

High pressure can cause spray gun to kickback. Hold 

spray gun with both hands during use.

 

WARNING:

 Risk of eye injury. Spray can splash 

back or propel objects. Always wear indirect 

vented (chemical splash) safety goggles, 

marked to comply with ANSI Z87.1 when 

using or in vicinity of this equipment. NEVER substitute 

safety glasses or dry-condition goggles for indirect 

vented safety goggles.

2

d

c

1

a

Reviews: