background image

Operator’s Manual 

20969 CRT Tiller

18

For additional information email 

[email protected]

 or call 800-345-6007 M-F 8-5

Engine Maintenance
Refer to the engine manual included in your parts packet for 

information on engine maintenance. Your engine manual 

provides information and a maintenance schedule for 

performing the following tasks:

1.  Always check oil level before starting engine. Refer to 

engine manual for capacity and type of oil to use.

2.  Change oil after first 5-8 hours of operation. Change oil 

while engine is warm. Refill with new oil of recommended 

grade.

4.  Check spark plug yearly or every 50 hours of operation.
5.  Service air cleaner.
6.  Keep engine and parts clean.
7.  Check engine and equipment often for loose nuts and 

bolts, keep these items tightened.

Check Tiller Transmission Grease

Check the grease level annually. To check the grease level:

1.  Cut out one of the cardboard stencils in the back of this 

manual. Take that dipstick cut-out and glue or tape it to a 

piece of cardboard cut out to match the stencil.

2.  Tiller must first be run for approximately 30 minutes to 

warm up grease for a proper measurement. Once warm 

let sit 5 minutes to allow grease to settle.

3.  Move tiller to level ground, making sure the transmission 

cover plate is level.

4.  Remove the gear case dipstick located between the 

handle bar mounts and the engine mount. 

      SEE FIGURE 11

5.   Insert the dipstick cut-out created in step 1 into the 

hole in the transmission cover plate so the top square is 

resting on the cover plate.  SEE FIGURE 12

6.  Remove the dipstick cut-out and check grease level. 

If level is in the bottom ADD area or not present, add 

grease in 200ml increments until grease level reaches a 

proper level reading (between 1” - 1 3/4” down from top 

of fill hole). DO NOT OVERFILL. The slashed, acceptable 

grease level area on the dipstick cut-out has a 200ml 

range.

NOTE: The front wheel transmission and rear tine 

transmission share a common reservoir. 

Recommended grease is Mystic 00, or equivalent, 

transmission grease. Oil must have an API - 

E.P (extreme pressure) rating of GL4 or lower. 

Higher E.P. rating (ie - GL5, GL6 etc) will cause 

the bronze components to soften. For partial 

fill-ups ( a few ozs or less) use SAE 140W or 85W 

gear oil or SAE 80W-90 weight gear oil with a API 

rating of GL4 or GL5. When replacing grease, the 

tiller transmission holds 18-22 ounces. DO NOT 

OVERFILL.

GEAR CASE

DIPSTICK

TRANSMISSION

COVER PLATE

20972-0005R1

FIGURE 11

FULL

ADD

DO NOT 

OVERFILL

1”

1¾”

BOTTOM OF SQUARE

RESTS ON COVER PLATE

ACCEPTABLE GREASE LEVEL

ADD GREASE

20972-0009R1

 FIGURE 12

GEAR CASE

DIPSTICK

TRANSMISSION

COVER PLATE

20972-0005R1

DO NOT PUT ENGINE OIL IN TRANSMISSION. 

TRANSMISSION LUBRICANT IS INSTALLED BY THE 

MANUFACTURER.

          CAUTION

Summary of Contents for 20969

































Reviews: