S19: Changing bag
S20: Changing mat (Colour may vary)
S21: Messy bag (Colour may vary)
Part List:
P1: Chassis
P2: Rear wheels x2
P3: Front wheel
P4: Carrycot mattress
P5: Carrycot liner
P6: Carrycot
Replacement Parts:
The replacement parts shown below are available for your product. For UK & Ireland customers, order through our
website: http://www.cosatto.com/service-centre/spares
For customer outside UK & Ireland, contact information for your local distributor can be found on
http://www.cosatto.com/stockists
If you require any further assistance, please contact us at [email protected]
S2: Chest pads (Set)
S3: Seat unit hood
S4: Seat unit
S5: Harness
S6: Crotch pad
S7: Rear wheel
S8: Basket
S9: Front wheel
S10: Carrycot carry handle /
seat unit bumper bar
S11: Bumper bar cover
S12: Carrycot mattress cover
S13: Carrycot mattress
S14: Carrycot liner
S15: Carrycot apron
P7: Carrycot hood
P8: Carrycot apron
P9: Carrycot carry handle
P10: Bumper bar with cover
P11: Seat unit hood
P13: Seat unit
P14: Changing bag (full)
P15: Raincover
S16: Carrycot
S17: Carrycot hood
S18: Raincover
Visual language Key:
Chassis
12-
Closing:
Note:
upright recline position.
While pressing the primary release button (1), pull both secondary levers (2) back.
Press down on the handle (3) until the autolock retains the chassis in the folded
position (4).
Fold handle inwards 2 to achieve the most compact fold (5).
Carrycot
13-
Preparation:
Remove mattress and liner from carrycot (1).
Unfold both frame bars until they locked into positions (2).
14-
Attach the carrycot handle to the carrycot (3).
There are a set of “D” ring located at the base of the carrycot for the attachment of a
separate safety harness approved to BS EN 13210 should this be required (harness not
supplied). Push the “D” rings through the slots in the liner (4).
15-
Fitting:
Note:
Dots are marked on the seat mounts and carrycot mounts (1). These should be on the
16-
Removing:
Note:
clear of the chassis.
Carrycot carry
handle
17-
Removing:
Carrycot hood
18-
Fitting:
19-
Adjusting:
20-
Removing:
Carrycot apron
21-
Fitting:
Removing is a reversal of this procedure.
Fitting & operation information:
Please refer to the following diagrams:
Chassis
1-
Opening:
Release the autolock (1) and lift the handle upwards until the chassis locks into position
(2).
Check the chassis has locked in place.
2-
Adjusting handle position:
Front wheel
3-
Fitting:
4-
Removing:
Rear wheel
5-
Fitting:
6-
Removing:
Brake
7-
Applying:
8-
Releasing:
Front swivel lock
9-
Applying:
10-
Releasing:
Basket
11-
Removing:
Summary of Contents for Nitty Gritty Giggle 2
