background image

April 5, 1999

569000264

E

IMI Cornelius Inc; 1999

IMI CORNELIUS INC  

g

  One Cornelius Place   

g

  Anoka, MN 55303-6234

Telephone (800) 238-3600                                      Facsimile (612) 422-3246

INSTALLATION INSTRUCTIONS

 

WHITE RODGERS ICE BANK CONTROL KIT (P/N 569000263)

ON

 UNIVERSAL C–750 PRE–MIX DISPENSERS

KIT FITS MODELS 2849949200, 2849949020, 2849959200, and 2849959020

IMPORTANT: All old parts (Ice bank Control Module and Mounting Bracket, Ice Bank Control Probe, and
the Ice Bank Control Probe Holder) must
 be returned to IMI Cornelius Inc, Attention: John Engstrom.
Send returned parts to the above address.

Read and understand these instructions thoroughly before installing this kit. Retain these instructions as part of
your equipment manual.

Table 1. Loose-Shipped Parts

Item

No.

Part No.

Name

Qty.

1

315794000

Ice Bank Control, White Rodgers

1

2

3528

Box, Ice Bank Control

1

3

186125000

Grommet,

1

4

313457000

Label, Hazard Shock

1

5

187188000

Screw, Machine, No. 8–32 X .250

2

6

3529

Holder, Control Bulb

1

7

180024000

O–Ring

2

8

3575

Electrical Wire, Black

1

9

3576

Electrical Wire, Red

1

10

325282000

Screw, Self Drilling, No. 8–18 Thread X .500 Long, No. 2 Point

2

11

32038900

Snap Bushing

1

12

040056000

Wire Tie

4

13

8901

Electrical Wire Terminal

1

14

330181000

Hex Nut

1

PREPARING DISPENSER FOR KIT INSTALLATION

WARNING: To avoid possible fatal electrical shock or serious injury to Installer, make sure
Dispenser is disconnected from power source before attempting to install this kit.

Summary of Contents for Remcor 2849949020








Reviews: