background image

Bottom Mounted Reach-In Refrigerators Installation Manual

© 2004, IMI Cornelius Inc.

- 1 -

Publication Number: 630460282INS

INSTALLATION MANUAL

Bottom Mounted Reach-In Refrigerators

COR23RRBM, COR49RRBMD

CAUTION

 - Only trained and certified electrical, plumbing and refrigeration technicians should 

service this unit. ALL WIRING AND PLUMBING MUST CONFORM TO NATIONAL AND LOCAL 
CODES.

I

NTRODUCTION

This manual contains instructions for installation, operation, and general maintenance of your 
commercial refrigerator. It also includes a Troubleshooting chart to diagnose problems along with 
corrective actions.

C

HECK

 

FOR

 S

HIPPING

 D

AMAGE

Prior to leaving the factory, each cabinet is thoroughly inspected and performance tested up to 12 hours 
to assure proper operating temperatures. 

Check the crate thoroughly for signs of shipping damage. If external damage exists, internal 
damage is also probable and uncrating should be done while the carrier’s representative is present. In 
any case, the equipment should be uncrated as soon as possible, preferably within five (5) days.

The manufacturer is not responsible for in-transit damage and the consignee must file any required 
damage claims directly with the carrier.

If damage is severe and obvious, write a brief description of the evidence on the carrier’s delivery receipt 
and above the carrier representative’s signature.

If hidden damage(s) is found, contact the carrier immediately (save all crating materials) and file the 
necessary freight claim with the carrier.

C

HECK

 

FOR

 A

CCESSORIES

Upon receiving the equipment, check that the shelves are inside the freezer, including the four clips or 
supports for each shelf.

Release Date: June 15, 2004

 www.cornelius.com

Revision: A

Summary of Contents for COR23RRBM









Reviews: