manualshive.com logo in svg

Copystar CS 181, Service Manual

Share
Download
Copystar CS 181 Service Manual Download Page 187

2KJ/2KH

1-5-35

(4) Detaching and refitting the laser scanner unit

Follow the procedure below to replace the laser scanner unit.

Procedure

1. Remove the original cover or the document 

processor.

2. Remove the rear cover (see page 1-5-6).

Remove the front left cover (see page 1-5-
47).
Remove the right upper cover, contact 
glass, rear upper cover and front scanner 
cover (see page 1-5-24).
Remove the left middle cover, left upper 
cover and slit glass (see page 1-5-26).
Remove the right middle cover (see page 1-
5-29).

3. Remove the screw and release three hooks 

and then remove the front right cover.

Figure 1-5-59

Front right cover

Screw

Front right 
cover

Hook

Hook

Hook

Summary of Contents for CS 181




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands