background image

150-412-181-01

March 31, 1998

Revision 01

HRU-412 List 8A

PairGain Engineering - Plant Series

 33

PairGain continues to repair faulty modules beyond the warranty program at 
a nominal charge. Contact your PairGain sales representative for details and 
pricing.

FCC Compliance

This unit complies with the limits for a Class A digital device, pursuant to 
Part 15 of the FCC rules.  These limits are designed to provide reasonable 
protection against harmful interference in a residential installation.  This 
equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio communications.  However, there is no guarantee that 
interference will not occur in a particular installation.  If this equipment does 
cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try 
to correct the situation by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Consult the dealer or an experienced radio or television technician for 
help.

Summary of Contents for 150-1103-81











































Reviews: