Main Features
Device connection
>
No Picture after providing power
May be the power supply voltage abnormity, please check
he power supply voltage and pole
whether exactitude
.
Please check all the connecting cable and monitors whether
be connected correctly or not
.
>
The picture level direction have flowing interference
ripples
May be caused by the power supply AC ripples, it need filter
the wave of the power supply
.
Check the monitor and peripheral equipments used.
>
The picture background color changes continuously
The fluorescent lamp’s electromagnetic field cause color roll.
This is proper phenomenon of the cameras.
Reduce the fluorescent lamp numbers or increase the
distance between the camera and the fluorescent lamps can
improve it.
Use power supply external sync. camera can solve it.
>
The picture smear too mass
The power supply’s voltage unstable
.
Connecting cables not connect correctly or have high
impedance.
Common Problems and Troubleshooting
1.Before using the camera ,please read this manual carefully and
keep it safely for later use.
2.Installation should be proceed by professional service and follow
manufacturer’s instructions, do not dismantle without authoriza
tion.
3.In order to prevent sensor ,do not expose lens to intense light
source in long time.
4.Do not touch sensor directly. Please covers the dustproof cover
when the camera is not being used.
5.Please use a dry soft cloth to clean the camera. If dirt difficult to
clean, use detergent with water and wipe dry the camera.
6.Do not install camera under air conditioning’s air gate ,or else
lens blur with condensation of moisture.
7.Please ensure that all electric power sources are turned off
when not open , installation ,clean, etc operation.
8.Please transporting , using and storing the camera in allowable
temperature and humidity.
9.If the camera was broken, for example power cord or plug dam-
aged,Splash liquid or foreign matter fall into camera, raining,
wetting, etc can’t work situation, please contact manufacturer
or maintenance center (modify and maintenance without perm
ission, you must be responsible for the problems).
Safety instruction
>
Auto Gain Control (AGC)
Built-in auto gain control
(AGC)
circuit. The color camera
Can get high definition picture in low Lux condition.
>
Auto Electronic Shutter (AES)
Built-in auto electronic shutter function. The color
camera’s AES speed can reach
1/100,000
s.
>
Gama Characteristic
Camera Gama characteristic
is
0.45
.
>
Signal Switch
Push “left” key above 5 seconds : CVBS
Push “right” key above 5 seconds : TVI
Push “up” key above 5 seconds : AHD
Push “down” above 5 seconds : CVI
Note:Once camera connecting to power supply, be sure to
switch the signal within 10 seconds, otherwise the signal will
be locked, and you need to enter the menu ,choose
”SYSTEM” —”TV SYSTEM”—”TV FORMAT” to switch TVI /
AHD / CVBS / CVI.
>
Menu
Note
:
• Please note the camera’s operating temperature and its
using environment
requirement. Avoid using the camera
at too high or too low temperatures. The operating tem
perature is -30~
+
60 . (Recommendatory operating tem
perature is -10~+50 .)
• Do not mount the camera near by the radiator
or heater.
• All Logos, Trademark, and Copyrights belong to their
respective owners.
IRIS
MANUAL / AUTO
FOCUS ADJ
OFF / ON
EXPOSURE
BRIGHTNESS / SHUTTER / SENS-UP / AGC
BACKLIGHT
OFF / HLC / BLC / WDR
DAY&NIGHT
EXTERN / AUTO / COLOR / B&W
DNR
MIDDLE / HIGH / LOW / OFF
IMAGE
SHARPNESS / GAMMA / MIRROR / FLIP /
ACE / DEFOG / RPIVACY
SYSTEM
TV SYSTEM / FRAME RATE / FREQ / IMAGE
RANGE / COLOR SPACE / COLOR BAR / LAN-
GUAGE / CAM TITLE / RESET
EXIT
SAVE / CANCLE
COLOR
AWB / COLOR GAIN / TV FORMAT
MOTION
OFF / ON
