manualshive.com logo in svg

Cooper Lighting WaveLinx Lite, User And Programming Manual, Page: 24 / 78

Share
Download
Cooper Lighting WaveLinx Lite User And Programming Manual Download Page 24

User Manual: WaveLinx Lite (1.5) 

24 

www.cooperlighting.com 

 

 

 

 
 

Part 2: Assign and Unassign Zones to Occupancy Sets 

If zones have been manually created, it will be necessary to assign them to an occupancy set for occupancy commands to operate. One 

occupancy set can have multiple zones assigned to it if the zones need to work together as a group. 
Internet connection is not required to assign zones to occupancy sets but connection to the WaveLinx Lite device/network is required. The 

mobile device will need to be in range and as close as possible (within 60 feet) of any WaveLinx Lite device that belongs to the area. 

 

To assign or unassign zones: 
1: With the mobile device, stand as close as possible to the WaveLinx device that has been provisioned in the area (within 60 feet).  
2: Open the WaveLinx Lite Mobile Application. 
3: In the site list, select a site. 
4: In the area list, select the desired area. 
5: Tap on the ‘Occupancy’ option to open the occupancy set list. 

 

Tap ‘+’ to add an 

occupancy set 

Created occupancy 

sets 

Tap ‘Occupancy’ 

Tap to rename 

Tap ‘Occupancy’ 

Select the site 

Select the area 

Summary of Contents for WaveLinx Lite















































































Reviews:

No comments