Questions?/Des questions?/¿Preguntas? 1-800-334-6871 [email protected]
1
PACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
Instruction Manual / Manuel d’instructions/ Instrucciones
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off an on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
•
This device contains transmitter module FCC ID: 2APB4-TGS2SCS2FR
(IC ID: 4706B-TGS2SCS2FR)
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
•
Install light 8-16 feet above the ground.
•
When installing two fixtures on one switch, make sure the switch is rated for at
least a 1 A inductive load.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE:
Fixture can be wall or eave mounted (Fig. 1).
NOTE:
Mounting bracket mounts to recessed mounted
standard junction boxes (Fig. 2). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application. For surface mount junction box
installation, refer to installation instructions included with
the adapter plate kit (E).
1.
Line up the slots on the mounting bracket (B) with
the holes on your junction box. Using either (2)
#6 screws or (2) #8 screws (D) (depending on
size of the holes in your junction box), attach the
mounting bracket (B) to your junction box (Fig. 3).
Be sure the mounting bracket is installed with the
funnel for the central mounting screw going into
the junction box.
2. Make the electrical connection between the
ground wire on the mounting bracket and the
ground wire inside of the junction box.
3. Disconnect the male connector in the back of the
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
•
Heed all warnings, including below warnings AND those included on product.
•
Save these instructions and warnings.
•
For outdoor use only.
•
cULus LISTED for wet location.
•
Disassembling your fixture will void the warranty.
•
Your fixture is prewired and preassembled for easy installation.
• Read and follow these instructions.
•
Risk of fire/electric shock. If not qualified, consult an electrician.
•
Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
•
Connect fixture to a 120-277 volt, 50/60 Hz power source. Any other connection
voids the warranty.
•
Fixture should be installed by persons with experience in household wiring or by
a
qualified electrician. The electrical system, and the method of electrically con
-
necting the fixture to it, must be in accordance with the National Electrical Code
and local building codes.
•
Fixture designed for wall or eave mount to a junction box only. Mount fixture
to a grounded, recessed-mounted standard junction box
marked for use in wet
locations.
•
Fixture can be mounted to an outdoor rated surface mount junction box when used
with the adapter plate kit. See kit instructions for proper installation methods.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following
2 conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
ENGLISH
WARNING
TGS2SCS2FRBLE40AB
TGS2SCS2FRBLE40AW
TGS2SCS2FSBLE40AB
TGS2SCS2FSBLE40AW
A. Light fixture
B. Mounting bracket
C. Gasket
E. Adapter Plate Kit
F. Decorative screw cover caps
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
1
Wall Mount
Eave Mount
Wall mount
Eave mount
Halo Home Flood
FIG.1
Wall mount
Eave mount
Halo Home Flood
FIG.1
2
1-1/2 in.
Round
FIG.3
1-1/2 in.
Octagonal
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
A. L
ight fixture
Appareil d’éclairage
Accesorio
C. Gasket
Joint d’étanchéité
Junta
F. Decorative screw cover cap
Cache-vis décoratif
Cubierta tapatornillos decorativa
B.
Mounting bracket
Support de montage
Soporte de montaje
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction
box screws
2 vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4
po pour boîtier de jonction
(2) cajas de empalmes de 6-32 x 3/4 pulgadas y de
8-32 x 3/4 pulgadas tornillos
G. Wire connector
Serre-fil
Conectores de cable
E.
Adapter Plate Kit
Trousse de plaque d’adaptation
Kit de placa adaptadora