background image

To Users

Thank you for selecting 

C&H

 product. Please read this instruction manual carefully before installing and using 

the product, so as to master and correctly use the product. In order to guide you to correctly install and use our 
product and achieve expected operating effect, we hereby instruct as below:

(1)  This equipment should be installed, operated or maintained by the qualified servicemen who have had 

specific training. During operation, all safety issues covered in the labels, User’s Manual and other 
literature should be followed strictly. This appliance can be used by children aged from 8 years and above 
and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge 
if they have been given supervision or instruction concerning used of this appliance in a safety way 
and understand the hazards involved. Children shall not play with the appliances. Cleaning and user 
maintenance shall not be made by children without supervision.

(2)  This product has gone through strict inspection and operational test before leaving the factory. In order to 

avoid damage due to improper disassembly and inspection, which may impact the normal operation of unit, 
please do not disassemble the unit by yourself. You can contact with the special maintenance center of our 
company if necessary.

(3)  For  personal  injury  or  property  loss  and  damage  caused  by  improper  operation  such  as  improper 

installation and debugging, unnecessary maintenance, violation of related national laws and rules and 
industrial standard, and violation of this instruction manual, etc., we will bear no liability.

(4)  When the product is faulted and cannot be operated, please contact with our maintenance center as soon 

as possible by providing the following information.

• 

Contents of nameplate of product (model, cooling/heating capacity, product No., ex-factory date).

• 

Malfunction status (specify the situations before and after the error occurs).

(5)  All the illustrations and information in the instruction manual are only for reference. In order to make the 

product better, we will continuously conduct improvement and innovation. We have the right to make 
necessary revision to the product from time to time due to the reason of sales or production, and reserve 
the right to revise the contents without further notice.

(6)  

The final right to interpret for this instruction manual belongs to 

Cooper&Hunter

.

Summary of Contents for CH-HP10SIRK3


























































Reviews: