manualshive.com logo in svg

CoolAutomation CoolMasterNet, Manual, Page: 41 / 47

Share
Download
CoolAutomation CoolMasterNet Manual Download Page 41

ASCII I/F

CoolMasterNet PRM   Rev 0.7

41

www.coolautomation.com

© 2017 CoolAutomation

OK

                     

feed

SYNOPSIS

feed [

UID

] [±]<TEMP[.d]> 

DESCRIPTION

This command defines CoolMasterNet Own Ambient Temperature (as if it were measured by CoolMasterNet
itself). Command can work in relative or absolute manner. If plus '+' or minus '-' sign precedes <TEMP>
parameter it's value will be added to or substituted from current value. Otherwise Own Ambient Temperature will
be set to the given <TEMP> value. <TEMP> can be provided with 0.1 precision. If <TEMP> is zero
CoolMasterNet will not use Own Ambient Temperature for it's operation. 
CoolMasterNet keeps separate Own Ambient Temperature for each Indoor Unit.

Own Ambient Temp usage depends on HVAC Line type.

HVAC Line

Own Ambient Temp usage

ME

If not zero, sent to Indoor Unit as Smart Controller temperature sensor value

M1M2

If not zero, sent to Indoor Unit as Wired Thermostat temperature sensor value

FUS
P1P2
H1H2
TAD

Temperature sent to Indoor Unit in i-feel message

EXAMPLE

Define Own Ambient Temperature to all Indoor Units on line L2

>

feed L2 24.5       

OK                  

Define Own Ambient Temperature to Indoor Unit 101 on line L1

>

feed L1.101 27     

OK                  

wh

SYNOPSIS

wh <

UID_STRICT

> <h|e|w|a|t<+|-|temp>|b<+|->>

wh <

UID_STRICT

>

DESCRIPTION

Control Water Heater Unit. When letter is omitted special water heater status is displayed.
 

Letter

Operation

Compatibility

ME

P1P2 (Altherma)

h

Heat Mode

P

e

Eco Mode

P

w

Hot Mode

P

a

Anti-freeze Mode

P

t

Tank (+=on, -=off, temp=set point)

P

b

Booster (+=on, -=off)

P

"no letter"

Print status

P

Summary of Contents for CoolMasterNet
















































Reviews:

No comments