manualshive.com logo in svg

CoolAutomation CoolMasterNet, Manual, Page: 37 / 47

Share
Download
CoolAutomation CoolMasterNet Manual Download Page 37

ASCII I/F

CoolMasterNet PRM   Rev 0.7

37

www.coolautomation.com

© 2017 CoolAutomation

swing

SYNOPSIS

swing [

UID

] <h|v|a|3|4|6|x>

DESCRIPTION

Set Indoor Unit(s) louver position to:

·

h - horizontal

·

v - vertical

·

a - auto (swing)

·

3 - 30º

·

4 - 45º

·

6 - 60º

Not all Indoor Units support louver position options listed about or have louver position control at all. Louver
control is capability of the specific Indoor Unit type. If requested louver position is not supported by Indoor
Unit(s), swing command will have no effect or will return an error.

EXAMPLE

Set Indoor Unit 102 on line L1 louver to horizontal position

>

swing L1.102 h   

OK                

Set all Indoor Units louver to 30º position

>

swing 3          

OK                

filt

SYNOPSIS

filt [

UID

]

DESCRIPTION

Reset Filter Sign.

EXAMPLE

Reset Filter Sign on Indoor Unit 102 0n line L1

>

filt L1.102 

OK           

Reset Filter Sign on all Indoor Units on Line L2 

>

filt L2*    

OK           

Reset Filter Sign on all Indoor Units

>

filt        

OK           

stat

SYNOPSIS

stat [

UID

]

stat2 [

UID

]

stat3 [

UID

]

Summary of Contents for CoolMasterNet
















































Reviews:

No comments