Form No. 610-40-12 (June, 2019)
Single-Panel Motor Operated Shutter
Models S24 - S36
Double-Panel Motor Operated Shutter
Models S42 - S60
Manually Operated Shutter
Models S24 - S60
1) These shutters have two tiebars. Before mounting the
shutter motor to the shutter, position the shutter motor on
the bracket as shown in Figure 4 or Figure 5, depending on
shutter motor model. Mount the motor and bracket to the
bottom of the inside face on the back of the shutter. Holes in
the shutter frame are pre-punched. Position the bracket so
that it is attached to the shutter frame along both the bottom
and side (See Figure 1). Use the nuts and bolts provided to
attach the bracket to the shutter frame.
2) With the shutter in the closed position, place a small
S-hook in the lower center hole in the left tiebar. Manually
rotate the operator arm so that it is pointing up. Cut the chain
linkage to the correct length and attach it to the small S-hook.
Attach the other end of the chain linkage to the large S-hook
on the operator arm. Crimp the S-hook closed. Remove and
discard the extra chain from the large S-hook in the operator
arm. Discard the extra S-hook, which is not used.
4) Check the voltage on the motor. Connect the wiring and
test the shutter’s operation. Adjust the linkage if necessary.
1) These shutter models consist of two panels divided by a
center rail. Before mounting the shutter motor to the shutter,
position the shutter motor on the bracket as shown in Figure 4
or Figure 5, depending on shutter motor model. Mount the
motor and bracket assembly to the bottom center of the
outside face on the rear of the shutter (See Figure 2). Holes in
the center rail and the bracket are pre-punched. Position the
bracket by aligning the holes in the left side of the bracket
with the holes in the center rail. Bolt the bracket to the center
rail using the 1/4” nuts and bolts provided.
Note: To avoid interference, the bolts must be
inserted with the heads on the inside of the shutter
and the hex nuts on the outside (bracket side).
2) With the shutter in the closed position, place a small
S-hook two of the center holes located in the factory-mounted
pull bar. Manually rotate the operator arm so that it is pointing
up. Cut the chain linkages to the correct length and attach
them to the S-hooks. Crimp the S-hooks closed. Connect the
other end of the chain linkages to the large S-hook on the
operator arm. Crimp the large S-hooks closed.
4) Check the voltage on the motor. Connect the wiring and
test shutter’s operation. Adjust the linkage if necessary.
1) The chain linkage should be mounted as outlined
previously for motor operation. Refer to figure illustrating
linkage for correct shutter model.
2) For manual operation, attach extra link of chain to S-hook
at point where operator arm is shown in figure.
3) Drill a hole (9/32” dia.) in the lower rail of shutter frame as
shown in Figure 3. Attach the eye-bolt with the provided
hardware as shown.
4) Thread the chain through eyelet of eye-bolt. Fasten chain
anchor on wall below shutter to provide anchor for lower end
of chain when shutter is in the “open” position.
3) Mount a return spring to the shutter frame using the
clamping screw. Align the return spring parallel to the chain
linkage. Connect the return spring wire to the upper center
hole in the left tiebar. Adjust the tension to hold the shutter
blades firmly closed. Discard the extra return spring.
3) Connect the return springs to the shutter frame using the
clamping screws. Align the return springs parallel to the chain
linkages. Connect the return spring wire to the upper center
hole in each tiebar. Adjust the tension to hold the shutter
blades firmly closed.
Installation Instructions—Other Side
Operation and Maintenance Instructions
for Type S Manual & Motor Operated Wall Shutters
Figure 1
S24 - S36
Figure 3
Chain
Linkage
Operator
Arm
Tiebar
Motor &
Bracket
Clamping Screw
Return Spring
Figure 2
S42 - S60
Chain
Linkage
Operator Arm
Tiebar
Motor &
Bracket
Clamping Screw
Return Spring
Pull Bar
Figure 5
Belimo Motor
Single
Panel
Double
Panel
Figure 4
Multiproducts
Motor
Single
Panel
Double
Panel
