Decora Wired
Keypad
Installation Guide
Supported model
C4-KCB-XX Decora® Wired Keypad
Introduction
The Control4® Decora Wired Keypad is intended for use in a Control4 system. It
installs in a standard US wallbox. Communication to the Control4 system is via RS-
485 protocol and wiring. For RS-485 wiring topologies, refer to the
Keypad Bus
Wiring Guide
(
ctrl4.co/buswiring
).
Box contents
•
Decora® Wired Keypad
•
Keycap Button Kit
•
Pluggable Terminal Block
• Warranty
card
Specifications
Model number
C4-KCB-XX
Power requirements
48VDC
Power consumption
Maximum 48V DC 1.2W
Minimum 48V DC 0.7W
Environmental
Operational temperature
0 to 40 ˚C (32 to 104 ˚F)
Humidity
5% to 95% non-condensing
Storage
-20 to 70 ˚C (-4 to 158 ˚F)
Miscellaneous
Control communications
RS-485
Weight
0.045 kg (0.1 lb.)
Shipping weight
0.14 kg (0.3 lb.)
Warnings and considerations
Important:
Using this product in a manner other than outlined in
this document voids your warranty. Further, Control4 is
not
liable
for any damage incurred with the misuse of this product. See
“Troubleshooting.”
Important:
Do
not
use a power screwdriver to install this device. If you
do, you may overtighten the screws and strip them. Also, overtightening
the screws may interfere with proper button operation.
Important:
This is an electronic device with intricate components.
Handle and install with care!
Caution!
Do not exceed the number of keypads per power supply as
indicated in the
Keypad Bus Wiring Guide
. Exceeding the maximum
number of keypads will result in overheating the wires and/or failed
devices.
Installation instructions
Caution!
When wiring the keypad, make sure that either:
•
The Bus Power Supply is
not
powered on.
- OR -
•
The pluggable connector is disconnected from the Bus Power
Supply.
1
Prepare the cable for termination by stripping the outer sheath and
individual wires, and then wire into the pluggable terminal block.
2
Wire the keypads as shown below.
Figure 1. Keypad wiring
Tip:
If you are using a Control4 push-on (screwless) faceplate in a
multi-gang installation, attach the black faceplate subplate to all of
the devices that will be installed into the wallbox
before
attaching the
devices to the wallbox. This will help ensure that all devices are properly
aligned and on the same plane after installation.
3
Fit the wires back into the wallbox.
4
Align the keypad to the wallbox (the model number label should be at the
bottom), then fasten it with the included screws.
Important:
Tighten the screws until the back side of the yoke plate is
even with the wall surface, but no further. Overtightening can warp the
keypad and cause it to malfunction.
5
Install the top actuator bar, bottom sensor bar, and buttons following the
instructions in the
Keypad Buttons Installation Guide
(
ctrl4.co/butn
).
6
Install the Control4 faceplate following the instructions in the
Faceplate
Installation Guide
or attach a standard Decora-style or square faceplate.
7
Ensure that the Bus Power Supply is installed correctly and powered on. For
instructions, see the
Bus Power Supply, 48V Installation Guide
(
ctrl4.co/bps48
).
KeyPad
KeyPad
V+
GND
D+
D-
V+
GND
D+
D-
To
Bus Ethernet
Gateway
To
Next Keypad
More help
For the latest version of this guide and to view additional materials, open the URL
below or scan the QR code. Your device must be able to view PDFs.
MOST RECENT VERSION
ctrl4.co/
dec-wrd-ig
BUS WIRING GUIDE
ctrl4.co/
buswiring
