1
FXE3000-EU
IEEE802.11n/a/b/g Wireless LAN
Access Point / Station Board
FXE3000-EU Setup Guide
CONTEC CO., LTD.
The FXE3000-EU is a wireless LAN board that conforms to IEEE 802.11n/a/b/g standards of various countries and
features a wide input power supply (5 to 30 VDC) and can be configured either as an access point or station.
Packing List
- Main unit (FXE3000-EU)...1
- Setup Guide...1
- Serial Number Label...1
- CE Declaration...1
Default setting
This product is set up via a network using a Web
browser. Connect this product to the PC with a
LAN cable using the wired LAN connection and
then access the default IP address in a web
browser. This product's default settings are shown
in the table to the right.
Setting Item
Default setting
IP Address
192.168.0.1
Subnet Mask
255.255.255.0
ESSID
LocalGroup
Security
Disable
Username
admin
Password
pass
Component Locations
(1) LAN port
(2) Power connector
(3) DC JACK
(4) INIT connector
(5) DIP Switches
(6) DIP LED
LED display
LED name
Status
Indicator
POWER
ON
Indicates that the device is operating.
Flashing
Indicates that the device is being started (This device turned on)
OFF
Indicates that the device is power off.
LAN
ON
Indicates that a wired LAN has been connected.
Flashing
Indicates that the product is transmitting/receiving data to/from
the connected terminal through wired LAN.
OFF
Indicates that a wired LAN not logged-in.
WLAN
ON
Indicates that the device has been connected.
Flashing
Indicates data is being transmitted to or received from the device
connected through wireless LAN.
OFF
Indicates that the device has been no connected.
POWER/ LAN/ WLAN
Flashing (simultaneously) Indicates that firmware has been reprogrammed. *1
POWER/LAN
Blinking twice / On
DHCP error
*1 Not include Log File
DIP switches
INIT connector
No. Name
Operation / function
No. Name
Operation / function
1
INIT Turning on this switch flashes the POWER,
WLAN LEDs. If the switch is turned off
before the LEDs change their status from
flashing to ON (about 3 seconds), all the
settings are restored to the default settings
after the product is started next time. Reboot
the product after the LEDs stop flashing. *1
1
INIT Short the INIT signal with the GND so
that the POWER, WLAN, and LAN LEDs
will flash. Then if you open the INIT signal
before the LEDs turn on (approx. 3
seconds), the settings are restored to the
default settings the next time the product
is started.
2
-
2
GND GND
Pin header (JP2)
LAN connector
No.
Name
Operation / function
No. Name
Operation / function
1 LAN port
4pin
The INIT (initialization) signal can be
connected to via pin 4 on the LAN port
by shorting pin 1 and pin 2.
1 TX+
Transmit (+)
2 TX-
Transmit (-)
2 INIT
3 RX+
Receive (+)
3 LAN port
5pin
The GND can be connected to via pin 5
on the LAN port by shorting pin 3 and
pin 4.
4 INIT/NC
Short the INIT signal with the GND so
that the POWER, WLAN, and LAN LEDs
will flash. Then if you open the INIT signal
before the LEDs turn on (approx. 3
seconds), the settings are restored to the
default settings the next time the product
is started. *1
* Usable when JP2 No. 1 and No. 2 are
connected.
4 GND
5 LAN port
7pin
The power supply line can be connected
to via pin 7 on the LAN port by shorting
pin 5 and pin 6.
6 24VDC
7
LAN port
8pin
The GND can be connected to via pin 8
on the LAN port by shorting pin 7 and
pin 8.
5 GND
GND
6 RX-
Receive (-)
8 GND
7 24VDC Power Supply
8 GND
GND
*1 Usable when JP2 No. 1 and No. 2 are connected. When initializing the product by turning the INIT signal on and off, the LEDs will continue
flashing for a short time after the signal is turned off. This indicates the internal memory files are being deleted. If the power is turned off while the
LEDs are flashing, the internal memory files may be damaged and the product may no longer be able to start properly. Always restart the product
after the LEDs stop flashing.
When supplying power via the LAN connector, do not use a combination of power supplied from the power connector and the AC
adapter.
- For PoE wire route only in the same building
Power Supply
Using the DC JACK
The power plug to be used must conform to EIAJ voltage classification 2.
When supplying power via the LAN connector, do not use a combination of power
supplied from the power connector and the AC adapter.
Using the Power connector
The power connector in Figure 1 can be used to
supply power from an external source. Use the
following power cable or its equivalent.
When supplying power from the power connector,
do not use a combination of power supplied via the
LAN connector and the AC adapter.
Figure 1
Power connector
Housing: JST S02B-PASK-2 (LF) (SN)
Cable: AWG28-16 (equivalent to it)
Pin No.
Nome
Operation / function
1
Vi+
(5-30VDC
±
5%)
2
Vi-
GND
When supplying the LAN cable power
- Create the power cable correctly as specified. Using the power cable with the
housing pins assigned wrong numbers may result in device faults or accidents.
- The input voltage range of this product is from 5 to 24 VDC ±5%. Supply
power outside that range may result in device faults or accidents.
- Use the power supply whose supply voltage rises to at least 4.75VDC within the
input voltage range within 10ms. Using a power supply which does not satisfy
this condition may result in device faults or accidents.
- Input voltage range: 5 to 30 VDC ± 5%. Use a power supply that rises to 4.75
VDC or higher in the input voltage range within 10 ms. There is a risk of
damage to the device or accident if a power supply outside this range is used.
Installation
Read and understand the following precautions before installation :
- Leaving a metal object in the vicinity of 30mm from the antenna board affects the antenna characteristics.
Do not place metal objects near the antenna as possible.
- This product has a protrusion of up to 14mm on the front surface and a protrusion of up to 3mm on the rear surface. Allow
clearance around this product and use it within the range of ambient temperatures satisfying the environment conditions for
installation.
- Figure 2 shows the locations the mounting holes for installing this product and external dimensions.
- Use M3 screws for the mounting holes (
φ
2.3 mm).
- The lower right mounting hole is the FGND (grounding) hole. Connect it to FGND (ground).
* 1 Always reboot the product after the flashing stops. The flashing continues for a little while after the product is switched off during
initialization by switching on and off the INIT switch. This indicates internal memory files are being deleted. The internal
memory files may be damaged and the product may not start up properly if the power is switched off before the flashing stops.
Connecting to This Product Using Web Browser
Start up a Web browser and enter the IP address of this product after “http: //” in the address bar. If connecting for the first
time, enter the default IP address. When the default setting IP address is 192.168.0.1, enter as follows.
Connecting to this product displays the “Wireless LAN
Manager” login screen/ If the login screen is not displayed,
the IP address setting for PC, browser settings, or the URL
entered in the address bar of the browser may be incorrect.
Enter a password on the login screen and then click “Login” to log in.
When connecting for the first time, Default setting is Username=”admin” & Password=”pass” and just click “OK”.
If the login is successful, the following setup screen will be displayed after a little while.
Setup Using Web Browser
Select the desired setting items from the opened menu (1).
Information such as setting items will be displayed in the
right-hand frame.
For more information about a setting item, please refer to
"help" (2).
Click “Submit” (3) after changing settings on each page to
temporarily save the settings in this product.
The settings become enabled when the product is restarted
after all the setup procedure is completed and the settings
are stored. Click “Save & Reboot” (4) on the left-hand
menu.
There will be no problem if you just save the settings now but reboot the product later when necessary. In this case, saving
the settings does not actually change the settings of the product. Therefore, make sure to reboot the product later
It takes approximately 5 - 10 seconds to save settings (writing to internal flash memory). During that period, the LEDs for
POWER, LAN and WLAN at the front part of the main unit blink simultaneously. Do not reboot or turn off the product until the
screen indicates the completion of the saving process. The setup file data and firmware data may be damaged and the product
may not operate properly if it is rebooted or switched off during the saving process.
WLAN
POWER
LAN
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION