manualshive.com logo in svg

Contec CONPROSYS M2M Series, User Manual For Communication Settings, Page: 73 / 103

Share
Download
Contec CONPROSYS M2M Series User Manual For Communication Settings Download Page 73

—

  PLC Communication Settings 

—

 

M2M Gateway PLC Communication Settings 

 

—

  73 

—

 

2.

 

Communication Troubleshooting 

This section lists items for you to check when PLC communication does not perform properly. 

 

 

Ethernet Communication 

- Is IP address of the communication partner correct? 
- Do the IP address segments of the communication partner and M2M Gateway match? 
- Is the network cable connected properly? 

-The CONPROSYS has a function for checking network connectivity. 

     Communication status between the CONPROSYS and the PLC can be checked. 
     *Some PLC units might be set not to return a ping response for security reasons. 
 
Go to the "Network" in the "Maintenance" menu. 
On the [ping], enter IP address of PLC in the "Target Address", then click the "Execute" button. 

 

 

 

 

If ping does not return a response… 

- Check the settings of LAN cable. 
- Check whether IP address of PLC is set properly. 

Reset the PLC settings if necessary. 

 

Other items to check 

- Is the communication setting mode appropriate or any trouble on it? 
- Is the communication port correct? Is the setting port not used for different communication? 

Summary of Contents for CONPROSYS M2M Series








































































































Reviews:

No comments