Contec CONPROSYS CPS-PCS341MB-DS1-1201 Reference Manual Download Page 22

Page: 22 / 65

—

Product Nomenclature and Function

—

CPS-PCS341MB-DS1-1201 Reference Manual (Hardware)

—

LED Indicator

Status of the product is indicated by ON/OFF and flashing of LED.
The meaning of each LED is described below.



LED Indicator 1

Color and Description

LED

Color

Display

Description

PWR

Green

Power has been supplied.

OFF

Power has not been supplied.

ST1

Green

Refer to the Reference Manual (Software).

ST2

Red

Refer to the Reference Manual (Software).

ERR

Red

It lights up when error occurs.

OFF

It indicates the system runs normally.

DIO0 - DIO3

Green

It lights up at the time of I/O.

OFF

It indicates there is no I/O.



LED Indicator 2

Color and Description

LED

Color

Display

Description

Green Flashing

It flashes at the SD access.

OFF

It indicates there is no SD access.

COM-RX

Green Flashing

It flashes when receiving data by the RS-232C.

OFF

It indicates data has not been received by the RS-232C.

COM-TX

Green Flashing

It flashes upon transmitting data by the RS-232C.

OFF

It indicates there is no data transmission by the RS-232C.

Summary of Contents for CONPROSYS CPS-PCS341MB-DS1-1201


































































Search results

Summary of Contents for CONPROSYS CPS-PCS341MB-DS1-1201

Reviews:

Related manuals for CONPROSYS CPS-PCS341MB-DS1-1201

Brands by name

Popular brands

Contec CONPROSYS CPS-PCS341MB-DS1-1201, Reference Manual

Search results

Summary of Contents for CONPROSYS CPS-PCS341MB-DS1-1201

Reviews:

Related manuals for CONPROSYS CPS-PCS341MB-DS1-1201

Brands by name

Popular brands