manualshive.com logo in svg

Contec CONPROSYS CPS-PCS341MB-DS1-1201, Reference Manual, Page: 21 / 65

Share
Download
Contec CONPROSYS CPS-PCS341MB-DS1-1201 Reference Manual Download Page 21

—

  Product Nomenclature and Function 

—

 

CPS-PCS341MB-DS1-1201 Reference Manual (Hardware) 

—

  21 

—

 

2.

 

Description of Product Components 

Components such as connectors, switches are described. 

1. 

 

Stack Bus 

It is used for power supply and communication to the configurable type module. 

 

 

CAUTION 

 

Never set or remove the product while power is active. 

 

Always confirm the PWR-LED is turned off before setting or removing the devices. 

 

 

 

2. 

 

Maintenance Connector 

Do not use this. (Maintenance purpose only) 

 

 

3. 

 

Power Connector 

Use the 3-pin connector, included in the package, to connect to external power.   
Connector type: DEGSON 15EDGK-3.5-03P-13-1000AH (or equivalent) 

 

 

 

Pin Assignment 

Pin No. 

Signal Name 

Description 

1 

V+ (24VDC) 

24VDC 

2 

V- (GND) 

Ground 

3 

FG 

Frame Ground 

 

Summary of Contents for CONPROSYS CPS-PCS341MB-DS1-1201


































































Reviews:

No comments