manualshive.com logo in svg

Contec CNT24-2GY, User Manual

Share
Download
Contec CNT24-2GY User Manual Download Page 56

 

6. Connecting with Expansion Accessories 

 

 

 

CNT24-2(USB)GY 

49 

6.

 

Connecting with Expansion Accessories 

When lacking of counter input channel used to connecting external device, you have to 

purchase a new same module, and thus it not only increases cost but also doubles 

installation space.    At the same time, adding channels is considered when designing 

this product, and additional module can be connected by the connector on module side, 

so that not only the cost but also the installation space are controlled. 

Up to 3 modules CNT24-2(FIT)GY can be connected when adding channels. 

In the case of combination of this product and three expansion modules “CNT24-

2(FIT)GY”, it is possible to control 16 channels output by way of one USB port. 

Table 6.1.  Expansion Module 

 

 

 

 

 

 

Figure 6.1. 

Expansion Module 

Points 

- Up to 3 modules can be connected. 

- Please use the supplied AC adapter when adding modules. 

- Modules with different function from this product can not be connected. 

 

Model

Output channel

Current consumption

Function

CNT24-2(FIT)GY

2

+5VDC 180mA (Max.)

Expansion module for CNT24-2(USB)GY

Up to 3 expansion modules   
can be connected 

With the same name 

Summary of Contents for CNT24-2GY










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands