manualshive.com logo in svg

Contec CNT24-2GY, User Manual

Share
Download
Contec CNT24-2GY User Manual Download Page 54

 

5. Troubleshooting 

 

 

 

CNT24-2(USB)GY 

47 

Returning to Initial State 

This is the method of returning to initial state.    It is suggested that you should return 

to initial state and perform installation again when the operation is losing stabilization. 

Moreover, the method of returning to the initial state is different depending on OS. 

Please initialize it by the method of suitable for OS used.   

 

Uninstall procedure for Windows 7, Vista, Server 2008, XP and Server 2003 

< Uninstall the device driver > 

Use [My Computer] - [Control Panel] - [Programs and Features] to uninstall the device 

driver. 

Select [Windows driver package - CONTEC (****)] and then click [Uninstall]. 

* 

"***" contains the driver category name (caio, ccnt, cdio, csmc, etc.). 

 

 

 

    Uninstall procedure for XP and Server 2003, use [My Computer] - [Control Panel] - 

[Add and Remove Programs] to uninstall the device driver. 

 

< Uninstall the development environment > 

Use [My Computer] - [Control Panel] - [Programs and Features] to uninstall the 

development environment. 

Select [CONTEC API-***(WDM) VerX.XX (development environment)] and then 

click [Uninstall]. 

* 

"***" contains the driver category name (AIO, CNT, DIO, SMC, etc.). 

 

CAUTION

Summary of Contents for CNT24-2GY










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands