Contec CNT24-2GY User Manual Download Page 52

Page: 52 / 73

5. Troubleshooting

CNT24-2(USB)GY

Version Upgrade

How to Upgrade the Firmware

Firmware is namely software which is embedded in module. Up-to-date firmware

(update file) will be supplied in the homepage of our company in the case of function

upgrade and so on.

The following presents how to update the update file downloaded from homepage to

module.

Step1 Removing module

Please make disconnection when USB port is being connected. When using self

power, remove AC adapter in order to reset status.

Step2 Set Module ID to FFh

Set Module ID - FFh.

It is special setting for firmware upgrade.

Point

Modules should be performed firmware version upgrade one by one.

Upgrade for multiple modules can not be performed at the same time.

Step3 Connecting

module

with USB port

Please connect USB port after AC adapter has been connected when using self power.

Step4 Starting firmware upgrade tools

Click on [Programs]-[CONTEC API-USBP(WDM)]-[Firmware upgrade tool] from

[Start] menu.

Module

ID(x16)

Module

ID (x1)

[F]

C E

Module ID FFh

Summary of Contents for CNT24-2GY










































































Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands

Contec CNT24-2GY, User Manual

Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands