& Ϯ ^ > , d & > K t ͗ ' d d / E ' d K < E K t z K h Z , d Z
CONTROLS
The DF2SL can be set for 1kW or 2kW heat output. This should be done on installation
using the selector switch within the heater. The heater will work with any of Consort’s
wireless controllers. A controller must be used or the heater will NOT work. (For more
information refer to the controller’s user guide.) On the front of the heater there is an
indication light. A green light indicates there is power to heater. The red light indicates
heat is enabled. A slow flashing red light indicates the room has reached the target
temperature. If the indicator light is flashing red rapidly and the heater is not responding
to controls it has overheated, see section “overheating protection”. Located on the left
hand side of the unit is a variable thermostat ranging from 5-35ºC. There are markings on
the thermostat. The single dot is equal to 5ºC and the four dots equal to 35ºC. Most
wireless controllers will also act as a thermostat. If the wireless thermostat is calling for
heat, the thermostat on the heater is allowed switch on/off. If the wireless controller is
calling for no heat the thermostat on the heater will not work. This is ideal for areas where
the controller can’t measure the same temperature as the heaters. For more information
on the functions of the wireless controllers refer to the specific user guide. If the
thermostat on the heater is not required, it can be disabled on installation. To disable,
simply remove the jumper on the circuit board within the heater. The jumper is located
just below the terminal block.
I F YOUR HEA TER DOES N OT WORK
·
Check that the light indicator is ON and power is available to the heater.
·
Check that the overheating protection has not operated. Follow the instructions
given under the section headed ‘Overheating protection’ .
·
Check that the fuse in the fused connection unit has not blown. This can be done
by replacing the fuse with another suitable fuse.
·
Should none of the above remedies work, then telephone the helpline number
shown in these instructions (UK ONLY). Do not attempt to repair the heater.
CUSTOMER H ELP LINE
Should you need any advice on the use of your new Consort product,
please contact our Helpline:
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: 01646 692172 Fax: 01646 695195
Email: technical@consortepl.com Web: www.consortepl.com
Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
BS EN ISO 9001 Registered Company No FM12671
57000832 Iss 01
,QVWDOODWLRQ 2SHUDWLQJ,QVWUXFWLRQVIRU
')6/+HDWéRZ)DQ+HDWHU
All electrical appliances produced by Consort are guaranteed for one year against
faulty materials or workmanship. This applies only if the appliance has been used for
purposes in accordance with the instructions provided and has not been connected to
an unsuitable electricity supply, subject to misuse, neglect, damage, modification or
repair by any person not authorised by us. This guarantee is offered to you as an extra
benefit and does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the
appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time of
printing. In the interest of progress Consort reserves the right to vary specifications without
notice.
O VER VI E W
Please read this guide carefully and retain for future reference and maintenance. This
appliance has been designed and manufactured to the highest international standards
but care should be taken in order to achieve the best results and highest safety. This
appliance also meets the requirements of EU Directive 2004/106/EC for EMC and
2009/125/EC Directive.
57000832 Iss 01