manualshive.com logo in svg

Congatec 065450, User Manual, Page: 50 / 75

Share
Download
Congatec 065450 User Manual Download Page 50

Copyright 

© 

2020 

congatec 

AG 

 

      DSTXm10 

       

50/75

7.1.2.5 

Chassis Power Control 

With “ipmitool chassis” command, you can view the power status of the conga-STX7 server. You can also power on or power down the server.

 

•

view the conga-STX7 chassis status

congatec@congatec-desktop:~$ sudo ipmitool chassis status

 

•

start the conga-STX7 server

congatec@congatec-desktop:~$ sudo ipmitool chassis power on
Chassis Power Control: Up/On

 

•

reset the conga-STX7 server

congatec@congatec-desktop:~$ sudo ipmitool chassis power cycle
Chassis Power Control: Cycle

 

•

shut down the operating system gracefully and power off the conga-STX7 to standby power mode

congatec@congatec-desktop:~$ sudo ipmitool chassis power soft
Chassis Power Control: Soft

 

•

power off the conga-STX7 server immediately from full power mode to standby power mode

congatec@congatec-desktop:~$ sudo ipmitool chassis power soft
Chassis Power Control: Soft

Summary of Contents for 065450












































































Reviews:

No comments