HAVELLS SYLVANIA EUROPE LTD
Avis Way Newhaven East Sussex BN9 0ED
www.havells-sylvania.com
3
÷
4 cm
35cm
Version in Class I
: earth required
Version in Class II
: earth not required
Version in Class III
: earth not required
•
Do not install in areas where snowplows are used.
IP66 - IP67 totally dust-proof and watertight against powerful water jets
will operate if occasionally submerged
heavy duty: can withstand impacts up to 6.5 Nm
mounting on normally inflammable surfaces allowed
replace the protection screen if damaged
with a plane float tempered glass – thickness 10 mm,
shock resistant 6.5Nm according to EN60598-1
getting rid of as urban waste forbidden
separate collection is mandatory when
the product is at the end of its life
EMBEDDED INSTALLATION WITHOUT PASSAGE OF VEHICLES
for correct assembly, proceed as follows:
1) avoid positioning the fixture in areas of subsidence (pict.1) where dirt and stagnant water
can accumulate. Picture 2
2) make a hole (boring) in the ground with a diameter of approximately 40/50 cm and approximately
80/100 cm deep.
3) square the upper part of the hole by inserting a prefabricated pit of approximately 40x40x40 cm.
The upper edge of the pit must be about 3/4 cm higher than the surrounding ground to
which it must be connected with an outer slope for the run-off of water and to avoid the
accumulation of dirt.
4) backfill the hole with a mixture of sand and gravel up to a distance of about 35 cm from the
upper edge of the pit. Hose with plenty of water until refusal and tamp the mixture in such
a way as to form a compact and homogenous draining layer.
5) place four bricks with a trowel of mortar on the bottom of the pit in order to form a solid
support base for the outer casing of the fixture which must protrude about 2/3 cm with
respect to the edge of the prefabricated pit.
6) backfill the pit around the casing with a mixture of well tamped and set sand
and gravel, arranging the cables for the electrical connection of the fixture.
EMBEDDED INSTALLATION WITH PASSAGE OF VEHICLES
proceed as in the above points 1-2-3-4.
5) refer to pict.3, prepare lean concrete cement on which to place the block of concrete, taking
care to leave a hole with a diameter of at least 20 cm for drainage. Provide for the passage
of electrical wires.
6) insert the outer casing of the fixture into a concrete foundation block, batched at 200 kg of 325 type
cement per cubic metre of mixture. The block must have a diameter (or side) of not less than 35 cm.
Line up carefully the upper edge of the outer casing with the trampling level as per pict. 3.
ELECTRICAL CONNECTION
Important: the electrical connection must be carried out by a skilled electrical. Important: in the
case of damage of the appliance, there may be a reduction in the degree of protection with
consequent infiltration of water and loss of insulation. Therefore, additional protection should
be inserted into the electrical plant against direct contacts (for example a high sensitivity
differential switch). During installation, fully respect the current rules on electrical systems.
• For the electrical connection use a flexible <HAR> rubber cable cross-section 1x1.5mm
2
.
The fixtures are complete with a piece of H07RN-F cable which is pre-connected and
sealed. For a rapid and safe connection with the electric line use the connector 4068964 or
an equivalent system that guarantees at least the IP67 degree.
N.B.: Fixtures complete with lamps: see catalogue.
installation and maintenance sheet
Pathè G/R4
product in compliance with the requirements
of the European Community Directories
* fixtures where it is possible to rotate the optic by ±45° by loosening out the screw of
the support of the reflector (fig.6) and to orientate the beam by ±25° on the vertical
plan, acting on the reflector.
Fixtures that can be utilized only in normally not accessible areas, according to
EN60598-2-13
version Class I
MH70W
max. glas Temp. ta 15°C
180° C
well tamped sand and
gravel backfill
fixture outer
casing
sand and gravel
draining foundation,
hosed until refusal,
well set and tamped
concrete block
lean concrete
pict. 2
pict. 3
draining layer
support bricks
fixed with a trowel
of mortar
connection
accessory 4068964
prefabricated pit
40x40x40cm
approx.
electric cables
pict. 1
YES
NO
electric cables
fixture outer
casing
upper casing
level flushing
to roadside
RELAMPING - MAINTENANCE
• cut off power from the mains before carrying out any type of maintenance.
• remove the fixture from the outer casing and take it to the edge of the ground.
(pict.4)
• carefully clean the fixture before opening it by the help of a big brush and of a
humid cloth.
• unscrew the frame (pict.5) and proceed with changing the lamp, respecting fully
type and power of lamp as shown on the label. Carefully read the instructions
supplied by the lamp manufacturer for its correct use.
• great care must be taken when changing the lamp, avoiding dirtying the
waterproof seal and relative support ledge. Check the gasket and replace
it if deformed. Make sure that the gasket is dead-centered in its housing.
For a correct operation it is necessary to arrange the unit so that its mouth is
horizontal.
• it is essential a frequent cleaning of the glass and of the outer surface of the fixture
to avoid build up of mud and dirtiness resulting in dangerous overheating due to
uncorrect light and heath dissipation.
• important: in the event of damage to the H07RN-F cable, breakage of the screen,
infiltration of water, the appliance cannot be used. Disconnect it from the mains
supply and contact our company or our sales organization for replacement/repair.
LED VERSION - RISK GROUP 2:
CAUTION: Possibly hazardous optical radiation emitted from this product. Do not
stare at operating lamp. May be harmful to the eye. The electrical circuit complete
with leds has to be required to our company or its distributors. The replacement must
be done by a qualified electrician.
pict. 4
pict. 5
pict. 6
270
Ø 2
15
20
0
TELLUX/T2
version Class I
E27
F18
MH20W
LED
Halogen
MH35W
version Class III
RGB
max. glas Temp. ta 25°C
60° C
60° C
70° C
45° C
70° C
45° C
75° C
Quality control: Should you have any complaint please get in touch with our company or its sales organization. Please give the number of your order as well as the serial number
that recognizes the fixture.
connection
accessory
4068964
Fixtures that can be utilized in all accessible areas, according to EN60598-2-13,
with exclusion of the areas where max. glass temp. 40°C is requested
Pedestrian and drive over, with max. glass temp. of 75°C
20kN static load resistance.
Features and meaning of the symbols shown on the label:
• lighting appliance for indoor and outdoor ground-recessed installation.
Capable of withstanding the load of motor vehicles with inflatable tyres pumped with
air, maximum weight static or dynamic: 3500Kg.
8 mm
frame
NB: These assembly instructions must be given to end users for correct maintenance and so that they know how to change the bulb. The appliance must not be tampered with or transformed and it must
be installed and used as supplied and in compliance with the National Rules on Installations. Any non-compliant installations will invalidate all forms of guarantee. The company cannot be held responsible
for damage caused by incorrect assembly. PRECAUTIONS FOR ASSEMBLY - IMPORTANT! As it is a drive-over ground-recessed appliance, great care must be taken in installation, scrupulously following
the assembly instructions specified here. • The appliance is tested for the penetration of water. • The appliance should be positioned and installed when closed, with the bulb already mounted and correctly
adjusted in order to avoid dirt entering and compromising its watertightness.
MI/1659-C- 7
a
edition - 05/2012
IS13158