manualshive.com logo in svg

Concoa Medical IntelliSwitch 570 Series, Installation And Operating Instructions Manual, Page: 42 / 52

Share
Download
Concoa Medical IntelliSwitch 570 Series Installation And Operating Instructions Manual Download Page 42

 

40 

Test 21 – Test Delivery Regulator Alarm 
Relay and Right Alarm Fault Light 

This test activates the delivery regulator alarm 
relay contact and lights the right delivery 
regulator fault light. 

 

 

Test 22 – Test Reserve Gas Supply Alarm 

This test activates the reserve gas supply 
alarm relay contact. 

 

 

 

Test 23 – Test Reserve Gas Active Relay 

This test activates the reserve gas supply 
active relay contact. 

 
 
 
 
 

Test 24 – Keypad test 

This test allows the testing of each function 
button on the front control panel and also 
indicates the status of the two toggle switches 
used to indicate the presence of the delivery 
regulators. 

When a button is pressed and held, a segment 
will light on one of the displays. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

Summary of Contents for Medical IntelliSwitch 570 Series





















































Reviews:

No comments