manualshive.com logo in svg

Concoa Medical IntelliSwitch 570 Series, Installation And Operating Instructions Manual, Page: 2 / 52

Share
Download
Concoa Medical IntelliSwitch 570 Series Installation And Operating Instructions Manual Download Page 2

 

i 

Index 

 

Safety ............................................................................................................................................ 2 

User Responsibility ...................................................................................................................... 4 

Installing the Medical IntelliSwitch™ ......................................................................................... 5 

Description of Product .................................................................................................................. 9 

Features ........................................................................................................................................ 9 

Operating the Medical IntelliSwitch™ ....................................................................................... 12 

User Selectable Features............................................................................................................. 13 

Setting Switchover Pressure ................................................................................................ 13 

Setting Delivery Regulator Pressure .................................................................................... 17 

Setting Delivery Regulator Tolerance.................................................................................. 19 

Setting Units of Measure ..................................................................................................... 20 

Setting Keypad Security Lockout ........................................................................................ 21 

Connecting to a Remote Alarm ............................................................................................ 22 

Setting Remote Alarm Outputs ............................................................................................ 24 

Connecting to External Alarms ............................................................................................ 27 

Enabling Reserve Gas Supply .............................................................................................. 28 

Enabling Remote Setup........................................................................................................ 29 

Setting Communication Mode ............................................................................................. 30 

Trouble Shooting ........................................................................................................................ 31 

Error Codes................................................................................................................................. 32 

Performing Self Test .................................................................................................................. 36 

Mounting Detail ......................................................................................................................... 43 

Power Requirements ................................................................................................................... 44 

Service ........................................................................................................................................ 44 

Self Test Worksheet ................................................................................................................... 45 

Factory Default Settings ............................................................................................................. 47 

Fail Safe Settings ........................................................................................................................ 48 

Warranty ..................................................................................................................................... 49 

 

Summary of Contents for Medical IntelliSwitch 570 Series





















































Reviews:

No comments