IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING AN ELECTRICAL FURNISHING, BASIC
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING THIS
FURNISHING
DANGER
–
TO REDUCE THE RISK
OF ELECTRIC SHOCK: ALWAYS UNPLUG THIS
FURNISHING FROM THE ELECTRICAL OUTLET
BEFORE CLEANING.
WARNING
–
TO REDUCE THE RISK
OF BURNS, FIRE, ELECTRIC SHOCK OR INJURY
TO PERSONS:
1.
Unplug from outlet before putting on or taking
off parts.
2. Close supervision is necessary when this
furnishing is used by or near children, invalids,
or disabled persons.
3. Use this furnishing only for its intended use
as described in these instructions. Do not
use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged
cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water.
Return the furnishing to a service center for
examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are
being used or where oxygen is being administered.
9. Never operate the furnishing with the air openings
blocked, keep the air openings free of lint, hair,
and the like.
10. To disconnect, turn all controls to the OFF or O
position, then remove plug from outlet.
11.
Be sure mirror is not in a position where it can
reflect sunlight; reflected sunlight can cause fire.
12. Do not use on a soft surface such as a bed,
where openings may be blocked.
13. Turn switch to OFF or O position, allow unit to
cool and unplug cord before replacing light bulbs.
14. Do not place or store this furnishing where it can
fall or be pulled into a tub or sink.
15. If this furnishing falls into water, unplug it
immediately.
Do not reach into the water.
16. Never use while sleeping.
17. Do not use bulb greater than 25 watts.
Use in any 120 volt, 60 hertz AC electric outlet
(ordinary house current). Do not use it in any
other electrical outlet.
18. To protect against electrical hazards, do not use
while bathing or in the shower.
19. Unplug the furnishing from outlet before
cleaning. Do not leave mirror unattended when
it is plugged in.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Wall Mount Mirror
1. Remove mounting bracket from base of mirror. Leave
long screws in bracket.
2. Using
3
/
8
-inch drill size, drill two holes in wall the same
distance apart as two opposite slots in bracket. Screw
into wall stud if possible. If drilling into stud, use
1
/
8
-inch
drill size. Otherwise, insert two wall anchors in holes.
CAUTION: Do not drill into electrical wiring through
wall. Check with electrician if necessary.
3. Screw bracket onto wall, into the anchors.
4. Attach mirror to bracket by placing long screws
through the two holes in mirror’s base. Secure
with knurled nuts. Cord should be extending
toward floor.
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this mirror has a
polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the
proper outlet. Never use with an extension cord unless
plug can be fully inserted. Do not change the plug
in any way.
1. Your lighted makeup mirror will adjust to many
different angles. Simply tilt the head backward or
forward to adjust to the desired angle. Your mirror will
also swivel so that you can use either the normal view
or the magnifying view located on the opposite side.
2. Plug into any standard wall outlet (120 volt AC).
Turn the rotary switch clockwise to the ON
or 1 position.
3. After use, turn switch clockwise again to the
OFF or O position.
TO REPLACE BULB
CAUTION: TURN OFF POWER AND UNPLUG.
ALLOW TO COOL AT LEAST 3 MINUTES BEFORE
REPLACING BULB.
Figure 2
Figure 1
NOTE:
Do not use a bulb greater than 25 watts.
Contact the Conair Service Center at 1-800-3 CONAIR
for replacement bulb information; ask for replacement
bulbs #RP65B. Bulbs are $5.99 each.
1. Unscrew and remove knurled thumb screws from
opposite sides of the mirror housing near the
rotating hinges (Fig. 1).
2. Carefully lift off the top half of the housing from the
bottom half that is affixed to the stand.
3. Unscrew the old bulb and replace with the new
bulb (Fig. 2).
4. Carefully replace the top housing half after locating
and aligning the screw holes to the bottom half. If
the holes don’t line up, turn top half of mirror 180˚.
5. Insert two knurled thumb screws into screw holes
and hand-tighten.
