IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
Read all instructions before using (this
furnishing).
DANGER -
TO REDUCE THE RISK OF ELEC-
TRIC SHOCK, ALWAYS UNPLUG THIS FURNISHING
FROM THE ELECTRICAL OUTLET BEFORE CLEANING.
WARNING –
T
o reduce the risk of
burns, electrocution, fire, or injury to
persons:
1. Unplug from outlet before putting on or
taking off parts.
2. Close Supervision is necessary when this
furnishing is used by, or near children,invalids, or
disabled persons.
3. Use this furnishing only for its intended use as
described in these instructions. Do not use
attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged
cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water.
Return the furnishing to a service centre for
examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or inser any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray)
products are being used or where oxygen is being
administered.
9. To Disconnect, turn all controls to the off position,
then remove plug from outlet.
10. Be sure mirror is not in a position where
it can reflect sunlight; reflected sunlight can
cause fire.
11. Do not block openings. Do not use on a soft
surface such as a bed, where openings may be
blocked.
12. Turn switch to “off” position and unplug cord
before replacing light bulbs.
13. Do not place or store appliance where it can fall
or be pulled into a tub or sink.
14. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
15. Never use while sleeping.
16. Do not use a bulb greater than 20 watts. Use
on any 120 volt 60 hertz AC electric outlet
(ordinary house current). Do not use in any other
electrical outlet. There is an electric outlet in base.
Do not plug in it any appliance over 12 amperes.
17. To protect against electrical hazards, do not use
while bathing or in the shower.
18. Unplug the appliance from outlet before cleaning.
Do not leave appliance unattended when it is
plugged in.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this furnishing
has a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change
the plug in any way.
1. Your circular, lighted makeup mirror will swivel so
that you can use either the normal, flat mirror or the
magnifying mirror located on the opposite side.
2. This Double-sided Mirror has a telescopic neck
which can be adjusted up or down 2 inches. Loosen
the knurled nut at the center of the neck by turning
the nut counterclockwise. Adjust the mirror to the
desired height and tighten nut clockwise.
3. Plug cord into any standard 120 volt wall outlet.
To turn on lights, simply turn the dial on the base to
desired light setting.
4. After use, always turn switch to the “OFF” position.
5. This mirror features an electrical outlet in the base.
Power ratings on appliances plugged into this electri-
cal outlet should not exceed 12 amperes.
6. The beauty and design of this mirror complements
any decor. Therefore, you may wish to leave the mirror
displayed. However, if you choose to store the mirror,
see “STORAGE” for detailed information.
SPECIAL FEATURES
This lighted makeup mirror uses incandescent light
bulbs with special coating, reproducing shadow-free
lighting in four different settings: evening, home, office
and day.
TO REPLACE BULB
CAUTION: TURN OFF POWER AND UNPLUG. ALLOW
TO COOL AT LEAST 3 MINUTES BEFORE REPLACING
BULB.
NOTE:
Do not use a bulb greater than 20 watts.
Contact a Conair service center at 1-800-3 CONAIR
for replacement bulb information (ask for replacement
bulb #RP34-clear, #RP35-blue). Bulbs are $1.50 a
piece, includes shipping and handling.
1. Unscrew and remove knurled thumb screws
from opposite sides of the mirror housing near
the rotating hinges. (Fig. 1)
2. Carefully lift off the top half of the housing from the
bottom half that is affixed to the stand.
3. Unscrew the old bulb and replace with the
new bulb. (Fig. 2)
4. Carefully replace the top housing half after locating
Figure 1
Figure2
