manualshive.com logo in svg

Comway 4G DTU, Configuration Instructions

Share
Download
Comway 4G DTU Configuration Instructions Download Page 17

 

17 

 

 

Modbus RTU ( master) to TCP (slave) protocol conversion. 

 

Up to 16 modbus tcp connection devices can be set. 

 

  RTU device ID==Configure the device address of the query command sent by 

the Scada software 

  TCP device ID==device address of the Modbus TCP device connected to the 

DTU network port 

  IP address == IP address of the Modbus TCP device connected to the DTU 

network port 

  Port = = the port number of the Modbus TCP device connected to the DTU 

network port 

8.

 

Modbus TCP to RTU configuration 

4G DTU in the program list of the configuration software MODBUS_ TCP 2 RTU , 

execute "Connect Device" on the main control panel . 

 

On the MODBUS_TCP 2RTU configuration page , set the relevant parameters for 

converting Modbus rtu to tcp protocol . 

Up to 8 Modbus rtu devices can be set , the device index number: 0-7. 

 

Each modbus rtu device needs to set the device ID and port number. 

 

RTU device ID == the address of the modbus rtu device connected to the DTU serial 

port. 

Summary of Contents for 4G DTU





















Reviews:

No comments

Brands by name

Popular brands

Load more brands