Comtrol WR7802-XT Series User Manual Download Page 91 | Manualshive

Page: 91 / 128

background image

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Cellular | SIM Security Settings Page - 89

Configuration Using the Web User Interface

Cellular | SIM Security Settings Page

This page allows you to assign the SIM security. If you (or ISP) already apply the PIN number to your SIM
card, you need to configure the correct PIN number for the WR7802-XT. After correctly enter the PIN number,
you can start the Cellular connection or change the new PIN settings.

Press

Apply

to activate the new settings.

Note:

You must

Save

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

SIM Security Settings

SIM

The currently selected SIM slot.

SIM Status

The current SIM status of the selected SIM slot.

Number of Retries
Remaining

Displays how many retries of entering the PIN on a SIM card before it
locks out.

SIM PIN

This is a pin code that locks the SIM card until you enter the correct code.
Use the pin to protect your account. The default code is set by the Service
Provider.

Remember PIN

Save the PIN code on this device. The system uses the saved PIN code to
unlock the SIM card automatically. Make sure that you use the Enable
PIN pin protections with this option.

PIN Protection

The following options are available:

•

Disable PIN

: The PIN code is removed from the SIM card.

•

Enable PIN

: Select this option when your SIM card is set with a PIN

code.

•

Change PIN

: Select this option when you need to change the PIN code

on your SIM card.

Beta

Version

«
...
89
90
91
92
93
...
»

Summary of Contents for WR7802-XT Series

































































































































Reviews:

No comments

Related manuals for WR7802-XT Series

Brand: Abocom Pages: 1

Brand: Ubiquiti Pages: 3

Brand: ?omtime Pages: 62

Brand: Draytek Pages: 8

AirStation G54 WLA2-G54

Brand: Buffalo Pages: 8

CyberPower RMCARD201

Brand: CyberPower Pages: 8

MP5S Plus Writer

Brand: SONIX Pages: 23

Brand: Digital Equipment Pages: 90

RuggedSwitch RS500

Brand: RuggedCom Pages: 16

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

MSR-20-21 ROUTER

Brand: H3C Pages: 83

Brand: CalAmp Pages: 52

Linktropy MINI-G

Brand: Apposite Technologies Pages: 57

Brand: Ubiquiti Pages: 13

Brand: Hornington Pages: 8

PowerTrans PT-7728

Brand: Moxa Technologies Pages: 8

Brand: Foscam Pages: 92

Brand: H3C Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands