manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Installation And Configuration Manual

Share
Download
Comtrol InterChange VS 3000 Series Installation And Configuration Manual Download Page 19

Configuring MultiProtocol Router (MPR)

19

Installing VS-Link (Novell)

7.

Press 

Enter

 to continue. The Installation Options menu displays.

8.

Select 

Exit

 and press 

Enter

. The list of Currently Installed 

Products is displayed.

9.

Press the 

Esc

 key until you exit from the install utility.

10. If needed, remove the installation media from the floppy drive.

11. Down and restart the server so that your changes take effect.

Configuring MultiProtocol Router (MPR)

Use the following procedures to configure the VS3000 to run with 
MPR 3.1A (or higher) or IntranetWare. These instructions assume 
that you have already:

•

Installed at least one ISDN line

•

Installed the VS3000 hardware

•

Installed the VS-Link software

•

Completed the checklist in the Working with the Phone Company 
section of this manual

Note: Some steps in the following procedure may differ depending 

upon your version of MPR. For help, press the 

F1

 key.

To begin, follow these steps:

1.

At the command line prompt, enter:

load inetcfg

The Internetworking Configuration menu is displayed:

2.

Select 

Boards

.

Summary of Contents for InterChange VS 3000 Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands