manualshive.com logo in svg

Comtrol DeviceMaster ATS-XPE, Installation And Configuration Manual

Share
Download
Comtrol DeviceMaster ATS-XPE Installation And Configuration Manual Download Page 61

Appendix A. Connectors

61 

AUX A and CONSOLE Port Connectors

AUX A and CONSOLE Port Connectors

This table illustrates the DB9 pinouts for the 

AUX A

 and 

CONSOLE

 connectors.

PARALLEL Port

This table illustrates the DB25 

PARALLEL

 pinouts.

Note:

The default printer is the Epson FX80.

Pin

Signal

Pin

Signal

Pin

Signal

1

CD

4

DTR

7

RTS

2

RxD

5

Ground

8

CTS

3

TxD

6

DSR

9

RI

Pin

Signal

Pin

Signal

1

Strobe#

14

Auto form feed #

2

Data 0

15

Error#

3

Data 1

16

Initialize

4

Data 2

17

Printer select line#

5

Data  3

18

Ground

6

Data  4

19

Ground

7

Data  5

20

Ground

8

Data  6

21

Ground

9

Data  7

22

Ground

10

Acknowledge

23

Ground

11

Busy

24

Ground

12

Paper empty

25

Ground

13

Printer select

26

Not connected

Summary of Contents for DeviceMaster ATS-XPE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands