manualshive.com logo in svg

Comtech EF Data Vipersat SLM-5650A, Installation And Operation Manual

Share
Download
Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 60

 

SLM-5650A Satellite Modem 

 

Revision 10 

 

Installation 

3–4 

MN-SLM-5650A 

3.2.1 

Install the Optional Rear Support Brackets Kit 

 

Feature 

Description 

1 

Back of Unit 

2 

Rack Enclosure Threaded Rear Mounting Rail (typical) 

Figure 3-3. Optional Rear Support Brackets Kit Installation 

 

Table 3-1. Optional Rear Support Bracket Kit Parts List 

KT/6228-X Rear Support Bracket Kit 

Item 

Quantity 

CEFD Part Number 

Description 

KT/6228-2 

KT/6228-3 

1 

2 

2 

HW/10-32SHLDR 

Screw, #10 Shoulder 

2 

4 

4 

HW/10-32FLT 

Washer, #10 Flat 

3 

2 

2 

HW/10-32SPLIT 

Washer, #10 Split 

4 

2 

2 

HW/10-32HEXNUT 

Nut, #10 Hex 

5 

4 

4 

HW/10-32x1/2RK 

Bolt, #10 Rack Bracket 

6 

2 

– 

FP/6138-2 

Bracket, Rear Support – 4” 

– 

2 

FP/6138-3 

Bracket, Rear Support – 10” 

 

 

 

 

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands