manualshive.com logo in svg

Comtech EF Data Vipersat SLM-5650A, Installation And Operation Manual

Share
Download
Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 291

 

SLM-5650A Satellite Modem 

 

Revision 10 

 

Appendix B 

B–21 

MN-SLM-5650A 

 

Figure B-4. Doppler Shift 

 

If the two earth stations are configured as master/slave, then the buffer need only be configured 
for Doppler operation. The buffer will then have sufficient capacity for the Doppler shift on the 
outward and return paths. 

A buffer set up for Doppler operation only will typically require less depth than one intended for 
both Doppler and plesiochronous operation. 

 

 

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands