Competition Pro TL-1041 Owner'S Manual Download Page 1

 

All content © Copyright TheLoudest.com 2004

 

   

 

OWNER

MANUAL 

2-WAY LOUDSPEAKERS 

CO-AXIAL/COMPONENT OPERATION 

REMOVABLE DOME TWEETERS 

 

SAFETY GUIDELINES | TECHNICAL SPECIFICATIONS 

FEATURES | INSTALLATION AND OPERATION INSTRUCTIONS 

   

 

All content © Copyright TheLoudest.com 2005 

Specifications (Per Pair) 

 

TL-1651 

TL-1051 

TL-1041 

Power Handling (Peak) 

400 watts 

350 watts 

300 watts 

Power Continuous (RMS) 

120 watts 

100 watts 

90 watts 

Frequency Response 

60 Hz – 22 kHz 

75 Hz – 22 kHz 

80 Hz – 22 kHz 

Sensitivity 

90 dB 

91 dB 

91 dB 

Impedance 

4 ohms 

4 ohms 

4 ohms 

Woofer section: 

Resonant Frequency (Fs) 

72 Hz 

88 Hz 

90 Hz 

Total Equivalent Factor (Qts) 

0.65 

0.71 

0.72 

Vol of Acoustic Susp. (Vas) 

16.72 lit 

5.83 lit 

2.86 lit 

Linear Excursion (Xmax) 

4 mm 

4 mm 

4 mm 

Displacement Volume (Vd) 

0.005 cutf 

0.0035 cuft 

0.002 cuft 

 
Tweeter 

1” Titanium dome 

1” Titanium dome 

1” Titanium dome 

Crossover 

6 dB / slope 

6 dB / slope 

6 dB / slope 

 

* Features & specification due to change without notice due to continued improvement and development. 

Summary of Contents for TL-1041







Reviews: