background image

About This Guide   vii

Compaq Confidential – Need to Know Required

Writer:

 Bob Young  

Project:

 Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide  

Comments:

 

Part Number:

 187194-001  

File Name: 

a-frnt.doc  

Last Saved On: 

4/6/00 7:10 PM

Cabinet Stability

WARNING:

  To reduce the risk of personal injury or damage to the equipment,

be sure that:

 

The leveling jacks are extended to the floor.

 

The full weight of the cabinet rests on the leveling jacks.

 

The stabilizing feet are attached to the cabinet if it is a single cabinet
installation.

 

The cabinets are coupled together in multiple cabinet installations.

 

Only one component is extended at a time. A cabinet may become
unstable if more than one component is extended for any reason.

Getting Help

If you have a problem and have exhausted the information in this guide, you
can get further information and other help in the following locations.

Compaq Technical Support

In North America, call the Compaq Technical Phone Support Center at
1-800-OK-COMPAQ.  This service is available 24 hours a day, 7 days a week.
For continuous quality improvement, calls may be recorded or monitored.

Outside North America, call the nearest Compaq Technical Support Phone
Center. Telephone numbers for world wide Technical Support Centers are
listed on the Compaq website. Access the Compaq website at

http://www.compaq.com.

Be sure to have the following information available before you call Compaq:

 

Technical support registration number (if applicable)

 

Product serial number

 

Product model name and number

 

Applicable error messages

 

Add-on boards or hardware

 

Third-party hardware or software

 

Operating system type and revision level

Summary of Contents for SSL2000 Series
















Reviews: