Comnet FDX721SHR Installation And Operation Manual Download Page 1

INS_FDX72SHR_REV–

02/29/12

PAGE 1

INSTALLATION AND OPERATION MANUAL 

FDX72(M,S)1SHR

multI-PRotocol RS232/422/485 DAtA tRANScEIVER  

FEAtuRING SElF-HEAlING RING oPERAtIoN

the comNet™ FDX72(m,S)1SHR series Self-Healing Ring transceiver unit is 
a fully-digital transceiver designed for implementing full RS232, RS422 or 
RS485 2 or 4-wire traffic signalization/communications data networks of the 
highest possible reliability. A network of FDX72SHR units can support one full-
duplex data channel or two half-duplex data channels. Full data re-clocking and 
regeneration permit an almost unlimited number of transceiver/controller units 
to be used within the network. these environmentally hardened transceivers are 
ideal for use in unconditioned out-of-plant or roadside installations. 

utilizing wave division multiplexing technology (WDm), only one optical fiber is 
required between units to implement a fully self-healing ring. two FDX72SHR 
units can be used in a redundant point-to-point topology.

Bi-color (Red/Green) lED indicators are provided for rapidly ascertaining 
equipment operating status including the location of fiber breaks. See 

Figure 7 

on 

Page 5

 for an explanation of lED indications.

these units are interchangeable between stand-alone or card-cage mount 
configurations. See 

Figure A

 on 

Page 7

 for mounting instructions.

See 

Figures 1 – 8

 for complete installation details.

Summary of Contents for FDX721SHR








Reviews: