manualshive.com logo in svg

CommScope SYSTIMAX iPatch Panel, Manager'S Manual

Share
Download
CommScope SYSTIMAX iPatch Panel Manager'S Manual Download Page 32

Guide:

 SYSTIMAX

®

 iPatch

®

 Panel Manager Guide

2–16

Task I. Configure the Network Settings

Before you configure the network settings for a Panel Manager with Network 
Manager module installed to be connected to the Ethernet network, contact your 
data network administrator to obtain the following information:

ƒ

the unique, static IP address to be used to identify the Panel Manager

ƒ

the subnet mask for your location

ƒ

the gateway required for communication with System Manager.

Perform the steps below to configure the network settings for a Panel Manager with 
Network Manager module installed.

1

At the Panel Manager display, press any button to turn on the lighting. From the 
Ready screen, press Menu.

2

Press 

Ê

 until the Panel Manager display shows:

3

With Change Network Settings highlighted, press Select.

The display shows:

4

Set the Network setting to Ethernet: 

a

With Network highlighted, press Select.

The display shows:

b

Press 

Ê

 to highlight Ethernet.

c

With Ethernet highlighted, press Save.

The Panel Manager sounds a confirmation tone.

                                 Rack 1
                Ready                 

   Menu  

 

  Alarms 

    

Jobs

  Test Panels                     
  Reset Panels
  Reset Racks
  Clear Memory

 

Change Network Settings

Highlight a command. Then press Select.

  Select                         Exit

  

Network: Off

  

  Select                         Exit

  
  Network:

 Off

           Ethernet
 

 NM LAN

Highlight a setting. Then press Save.

   Save                         Cancel

Summary of Contents for SYSTIMAX iPatch Panel
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands